ENG
LISH
ANTMIX Series
| User manual
4
5
SERIES
User manual
|
ANTMIX
Series
9 EQ - CHANNELS FROM 9 TO 12 (16FX USB) / FROM 17 TO 20 (24FX USB)
Use this four-band equalizer to boost or to cut the high, mid and lo frequencies to get the best mix in
any environment.
10 AUX 1 & 2
These knobs adjust the signal sent to AUX SEND 1 and 2. both sends can be set pre-/post-fader.
11 AUX 1 & 2 PRE/POST
This selector determines whether the AUX 1and 2 send level is independent (PRE) or is influenced (POST)
by the channel level control. Generally it is used PRE to send the signal to stage monitors or IEM, POST
to send the signal to an external effect unit.
12 AUX 3
This post-fader send, i.e. dependent on level control of its channel, allowing to adjust the signal sent to
an external effect unit or to a monitor connected to the AUX SEND 3 output.
13 DFX POST
This send, influenced by the individual channel level control, adjusts the signal sent to the internal effects
or to an external effects connected to DFX SEND output. Furthermore, the DFX POST control can be used
as the fourth auxiliary send (deactivating the internal effect via the DFX MUTE button) for connection to
an external effects unit connected to the AUX SEND 4 output.
14 PAN - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
This knob adjusts the signal position in the stereo field.
15 BAL - CHANNELS FROM 9 TO 12 (16FX USB) / FROM 17 TO 20 (24FX USB)
The BAL knob sets the left-right balance for stereo channels.
16 MUTE & LED
Press this button to mute the selected channel source.
The lit LED indicates the MUTE activation.
17 SOLO & LED
Press this button to check channel signal level before the fader.
It works also when the channel is muted; the led indicates the activation of the command.
18 GR 1-2
Press this button to route the channel signal to GROUP OUT 1-2 outputs.
19 GR 3-4
Press this button to route the channel signal to GROUP OUT 3-4 outputs.
20 L-R
Press this button to route the channel signal to MAIN MIX L-R outputs.
21 VOLUME
Use this fader to adjust overall channel volume.
22 SIG LED
This led is light when the input signal is very strong and it's close to distortion.
If the LED is continuously lit, you need to reduce the VOLUME of the fader or cut the channel EQ by
reducing the boost introduced by the HI-MID-LOW tone gains.
1 LINE L (MONO) & R INPUT
Two 6.35 mm. (1/4”) balanced line input.
Connecting only one cable to L/MONO, it becomes a mono channel. You can also use an
unbalanced cable.
2 GAIN & CLIP LED
This knob adjusts the gain of the microphone or line signal, turn it to the right to raise the
level, or to the left to decrease it.
The CLIP LED is lit when the input signal is too high.
3 LINE/USB
Press this switch to assign channels 15/16 (16FX USB) and 23/24 (24FX USB) to the USB
interface and receive the audio signal from the computer connected to the unit. In the LINE
position, key released , the channels are normally assigned to the respective inputs jack.
4 EQ
Use this four-band equalizer to boost or to cut the high, mid and lo frequencies to get the
best mix in any environment.
5 AUX 1 & 2
These knobs adjust the signal sent to AUX SEND 1 and 2. Both sends can be set pre-/post-fader.
6 AUX 1 & 2 PRE/POST
This selector determines whether the AUX 1and 2 send level is independent (PRE) or is
influenced (POST) by the channel level control. Generally it is used PRE to send the signal to
stage monitors or IEM, POST to send the signal to an external effect unit.
7 AUX 3
This post-fader send, i.e. dependent on level control of its channel, allowing to adjust the
signal sent to an external effect unit or to a monitor connected to the AUX SEND 3 output.
8 DFX POST
This send, influenced by the individual channel level control, adjusts the signal sent to the internal
effects or to an external effects connected to DFX SEND output. Furthermore, the DFX POST
control can be used as the fourth auxiliary send (deactivating the internal effect via the DFX
MUTE button) for connection to an external effects unit connected to the AUX SEND 4 output.
9 BAL
The BAL knob sets the left-right balance for stereo channels.
10 MUTE & LED
Press this button to mute the selected channel source.
The lit LED indicates the MUTE activation.
11 SOLO & LED
Press this button to check channel signal level before the fader.
It works also when the channel is muted; the led indicates the activation of the command.
3.1.2
|
STEREO INPUTS
13/14 - 15/16 (ANTMIX 16FX USB) / 21/22 - 23/24 (ANTMIX 24FX USB)
9
1
2
3
4
9
10
11
5
6
7
8
14
10
11
13
12
15
16
18
19
20
22
21
17
