manualshive.com logo in svg

Ankom ANKOM200 FIBER ANALYZER, Руководство оператора

Поделиться
Скачать
Ankom ANKOM200 FIBER ANALYZER Скачать руководство пользователя страница 20

Operator’s Manual

 

 

 

 

 

 

 

 
pg. 20 

 

Rev 1/24/20 

 

9.

 

  Seal the filter bag within 4mm of its open end. Keep the sealer arm down for 2 – 3 seconds after the red sealer light 

turns off (to cool the seal). The seal can be seen as a solid melted stripe along the top edge of the filter bag. If the seal 
is not strong, re-seal the bag. 

10.

 

  To eliminate sample clumping, spread the sample out uniformly within the filter bag by shaking and flicking the bag. 

11.

 

  Repeat steps 5 – 10 for all filter bags that will be used in the Analyzer. (Up to 24 bags can be processed during one 

procedure with one of the bags being a blank.) 

 

IMPORTANT: 

If your samples contain soybean products or >5% fat

…

 

Before  doing  the  NDF  analysis  in  the  ANKOM

200

,  you  will  need  to  do  a  pre-

extraction. For samples containing non-roasted soybean or >5% fat, follow the pre-
extraction steps below: 

1.

 

Place the filter bags with sample (up to 23) into a container with a top. 

2.

 

Pour enough fresh acetone into the container to cover the bags. 

3.

 

Put the top on the container. 

4.

 

Shake the container 10 times and allow bags to soak for 10 minutes. 

5.

 

Pour out and dispose of the acetone. 

6.

 

Execute steps 1 through 5 a total of two times. 

7.

 

Place the bags on a wire screen to air-dry. 

If your samples contain roasted soybean…

 

Follow the pre-extraction steps below: 

1.

 

Place the filter bags with sample (up to 23) into a container with a top. 

2.

 

Pour enough fresh acetone into the container to cover the bags. 

3.

 

Put the top on the container. 

4.

 

Shake the container 10 times. 

5.

 

Pour out and dispose of the acetone. 

6.

 

Pour  fresh  acetone  into  the  container  and  allow  the  samples  to  soak  for 
twelve hours. 

7.

 

Pour out the acetone. 

8.

 

Place the bags on a wire screen to air-dry.

 

 

 

12.

 

  Place the filter bags with sample and at least one empty bag (used as a Blank) into the Bag 

Suspender trays as shown (maximum of three bags per tray). 

 

13.

 

  Stack each tray on the Bag Suspender rod (eight trays in total) with each tray rotated 120 

degrees from the tray below. 

 

IMPORTANT: 

You must use all eight trays even if they are empty. 

 

14.

 

  Add the 9

th

 tray to the top of the Bag Suspender rod. This tray contains no filter bags and acts as a cover. 

 

NOTE: 

The samples are now ready for the NDF analysis procedure. 

 

 

 

 

Содержание ANKOM200 FIBER ANALYZER







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды