Ametek VERSITRON BT130R Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 82

Ametek VERSITRON BT130R Скачать руководство пользователя страница 69

Versitron Operation Manual

69

8.0

MAINTENANCE & TROUBLESHOOTING

8.1

Maintenance Procedures

The Versitron needs no regularly scheduled maintenance other than calibration. For
highest accuracy; anvils, indenters and indenter shrouds should be checked for
damage and dirt on an occasional basis or when changed. The Vee anvil alignment
should also be checked regularly especially before testing small diameter rounds.

8.2

Troubleshooting “What Not To Do”

Do not open the test head except at the direction of the Newage Customer Service
manager. Unauthorized opening of the test head voids the warranty.

If you think you may need service, please review the troubleshooting guide before you
call in so that Newage will be in a position to provide assistance. Newage is eager to
provide service and assistance, but our ability to help will be hampered by inadequate
information.

8.3

Troubleshooting “What to Do” Before You Call Newage

•

Get the model and serial number of the tester, indicated on the label on the back of

head.

•

Get an exact description of the problem, be as specific as possible.

•

Review the Pre-Troubleshooting Checklist and verify the tester is being used

correctly.

•

Review Section Troubleshooting Guide to see if the problem is easily corrected at

your facility.

8.4

Pre-Troubleshooting Checklist

(Review appropriate section in manual for corrective action.)

•

Are the correct loads and indenter being used for the desired scale?

•

Is the Indenter shroud properly installed?

•

Is the contact area worn or deformed? (If questionable, substitute another shroud if

available).

•

Is the indenter chipped or flattened? (If questionable, substitute for a different

indenter and check calibration).

•

If checking round specimens, is the Vee anvil alignment O.K.?

•

Is the test head installed properly?

•

Is the stand set up correctly?

•

Are all the connectors tight and the power on?

If all these items have been checked, please continue to the next section.

«
...
67
68
69
70
71
...
»

Содержание VERSITRON BT130R



















































































Отзывы:

Нет отзывов