manualshive.com logo in svg

Amersham Pharmacia Biotech AKTA design pH/C-900, Руководство пользователя

Поделиться
Скачать
Amersham Pharmacia Biotech AKTA design pH/C-900 Скачать руководство пользователя страница 34

EMC standards

This product meets the requirement of the 
EMC Directive 89/336/EEC through the 
harmonized standards EN 50081-1 
(emission) and EN 50082-1 (immunity)
Note: The declaration of conformity is valid 
for the instrument when it is
• used in laboratory locations
• used in the same state as it was 

delivered from Amersham Pharmacia 
Biotech except for alterations described 
in the user manual

• used as “stand alone” unit or 

connected to other CE labelled 
Amersham Pharmacia Biotech 
instruments or other products as 
recommended.

S

afety standards

This product meets the requirement of the 
Low Voltage Directive (LVD) 73/23/EEC
through the harmonized standard 
EN 61010-1.

Monitor pH/C-900

User Manual 18-1120-06 Edition AC

30

C 

Reference information

18-1120-06_AC.qxd  1999-04-14 14:16  Sida 30 (1,1)

Содержание AKTA design pH/C-900









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды