manualshive.com logo in svg

Amersham Pharmacia Biotech AKTA design pH/C-900, Руководство пользователя

Поделиться
Скачать
Amersham Pharmacia Biotech AKTA design pH/C-900 Скачать руководство пользователя страница 28

B.2.4 Setting up pH temperature compensation

The relationship between pH and the output signal from the pH
electrode is temperature dependent. For more accurate measurements
during temperature changes, the pH measurement can be
temperature compensated. In normal applications, if the temperature
of the buffers and calibration buffers are identical, temperature
compensation does not need to be on.

When using temperature compensation it is important that the
temperature of the pH electrode is the same as that of the
conductivity flow cell since that is where the temperature is
measured.

1 Select main menu 

Setup

, press OK.

2 Select menu 

Setup pH

, press OK.

3 Select sub menu 

Setup pH Temp Comp

, press OK. 

4 Set the temperature compensation on or off, press OK.

B.2.5 Setting up the pH display

Normally the pH is displayed in the main operating menu or its
alternative (see section 3.4 Reading pH and conductivity values). If
not required the pH display can be set to off.

1 Select main menu 

Setup

, press OK.

2 Select menu 

Setup pH

, press OK.

3 Select sub menu 

Setup Show pH

, press OK. 

4 Set the pH display on or off, press OK.

B.2.6 Calibrating the temperature sensor 

Calibration of the temperature sensor in the conductivity flow cell is
only necessary if the monitor is used in high accuracy measurement
or the conductivity flow cell is replaced.

1 Place the flow cell together with a precision thermometer inside a

box or empty beaker to ensure that they are not exposed to draft.
Leave them for 15 minutes to let the temperature stabilise.

2 Read the temperature on the thermometer.

3 Select main menu 

Setup

, press OK.

4 Select sub menu 

Setup Temperature

, press OK. 

5 Select sub menu 

Setup Adjust Temp

, press OK. 

6 A warning message will be displayed, press OK.

7 Enter the temperature shown on the thermometer, press OK.

Monitor pH/C-900

User Manual 18-1120-06 Edition AC

24

B 

Reference information

Warning! This will
change temp calib

Setup Adjust Temp
(23.5°C)

Setup Temperature

Setup Adjust Temp
(23.5°C)       25.0

Setup Show pH
(On)

Setup pH Temp Comp
(Off)        On Off

Setup pH

18-1120-06_AC.qxd  1999-04-14 14:16  Sida 24 (1,1)

Содержание AKTA design pH/C-900









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды