manualshive.com logo in svg

Amersham Pharmacia Biotech AKTA design pH/C-900, Руководство пользователя

Поделиться
Скачать
Amersham Pharmacia Biotech AKTA design pH/C-900 Скачать руководство пользователя страница 13

3.6

Calibrating pH (optional in ÄKTApurifier systems)

A good laboratory routine is to calibrate the instrument once a day,
when the electrode is replaced and if the ambient temperature is
changed. The pH monitor is calibrated using standard buffer
solutions in a two point calibration. The two buffer solutions can
have any pH value as long as the difference between them is at least
1 pH unit. Calibration can also be performed from UNICORN. In
UNICORN select 

System Control:System:Calibrate

. Select the pH

monitor. The calibration procedure can be done with the pH
electrode either fitted in or removed from the flow cell.

Calibrating with the electrode outside the flow cell

When calibrating the electrode out of the flow cell and changing
from one buffer to another, rinse the electrode tip with distilled
water and dab it carefully with a soft tissue to absorb the remaining
water. Do NOT wipe the electrode as this may charge it and give
unstable readings. 

The steps below describe the procedure used with the electrode
removed from the flow cell.

Note: The Monitor must be unlocked if connected to a UNICORN
control system.

1 Remove the pH electrode from the flow cell and immerse the

electrode in the 1:st standard buffer solution (normally pH 7.0).

2 Select main menu 

Calibrate pH

. The display shows the current

low and high calibrated pH value. Press OK.

3 Select sub menu 

Calib pH Buffer 1

, 

press OK. When the pH value

has stabilized, the 

Please wait

message will disappear.

4 Adjust the pH value in the display using the dial, so that it

corresponds to the known pH value of the 1:st buffer solution,
press OK. The sub menu 

Calib pH Buffer 2

is shown.

5 Rinse the electrode tip with distilled water and then immerse the

electrode in the 2:nd standard buffer solution (e.g. 4.0 or 9.0),
press OK.

6 When the pH value has stabilized, the 

Please wait

message will

disappear.

7 Adjust the pH value in the display using the dial, so that it

corresponds to the known pH value of the 2:nd buffer solution,
press OK. 

Monitor pH/C-900
User Manual 18-1120-06 Edition AC

9

Operation 

3

Calib pH Buffer 1

Calib pH Buffer 2

Calibrate pH
(7.00 – 10.00)

18-1120-06_AC.qxd  1999-04-14 14:16  Sida 9 (1,1)

Содержание AKTA design pH/C-900









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды