American Standard Schlage Link AZEMT500BB32MAA Скачать руководство пользователя страница 27

27

Warranty

Limited Warranty 

Low Voltage Room  

Comfort Controls

U.S.A. and Canada Only
This limited warranty is extended by the manufacturer to the original purchaser and to any succeeding owner of the real property to which the 
low voltage room comfort control is originally affixed and applies to products purchased and retained for use within the U.S.A. and Canada.
The limited warranty period begins when the low voltage room comfort control installation is complete, verified by installer’s invoice or similar 
document. If installation completion and start-up date cannot be verified by installer’s invoice or similar document, limited warranty coverage 
begins six (6) months after the date of manufacture based on the low voltage room comfort control serial number.
If any part of your low voltage room comfort control fails because of a manufacturing defect within five (5) years from the date the limited 
warranty period begins, Warrantor will furnish without charge a new low voltage room comfort control. Any local transportation, related service 
labor, and diagnosis calls, are not included.
This limited warranty does not apply if the low voltage room comfort control was purchased direct (i.e. from internet websites or auctions) on 
an uninstalled basis. Additionally, this limited warranty will not apply unless the low voltage room comfort control is: (1) installed by a licensed 
or qualified HVAC technician, (2) applied and installed in accordance with the manufacturer’s recommendations in its Installer’s Guide, and (3) 
in compliance with all industry standards, national, state, and local codes.
This limited warranty does not cover your low voltage room comfort control if it is damaged while in your possession; including, but not limited 
to (1) damage caused by unreasonable use of the low voltage room comfort control, (2) damage from failure to properly maintain the low 
voltage room comfort control as set forth in the Use and Care manual, (3) damage that is not considered a manufacturing defect, such as acts 
of God, malfunctions or failures resulting from fire, water, storms, lightning, earthquake, theft, riot, misuse, abuse, increased utility usage costs,  
(4) performance problems due to improper selection/equipment match-up, installation, or application, or (5) failures, defects, or damages 
(including, but not limited to, any failure or loss of data) caused by any third party product, service, or system connected or used in conjunction 
with your low voltage room comfort control.
THE LIMITED WARRANTY AND LIABILITY SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES AND LIABILITIES, 
WHETHER IN CONTRACT OR IN NEGLIGENCE, EXPRESSED OR IMPLIED, IN LAW OF IN FACT, INCLUDING IMPLIED WARRANTIES 
OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE, AND IN NO EVENT SHALL WARRANTOR BE LIABLE FOR ANY 
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow limitations on how long an implied limited warranty lasts or do not allow the exclusion or limitation of incidental or 
consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you 
may also have other rights which vary from state to state.
Parts will be provided by our factory organization through an authorized service organization in your area listed in the yellow pages. If you wish 
further help or information concerning this limited warranty, contact:
Residential Systems 
6200 Troup Highway  
Tyler, TX 75707 
Attention: Consumer Relations
Or visit our website: www.americanstandardair.com
TW-1019-5109

Содержание Schlage Link AZEMT500BB32MAA





























Отзывы: