manualshive.com logo in svg

American Standard Schlage Link AZEMT500BB32MAA, Инструкция по установке и эксплуатации

Поделиться
Скачать
American Standard Schlage Link AZEMT500BB32MAA Скачать руководство пользователя страница 22

22

The Installer Settings screen is a hidden screen designed for use by qualified installers and service technicians. Do not change any 
settings in these screens unless you are a qualified installer or service technician.

Installer Settings

Display Lock 

N

System Settings

Max Heat SP 

90

Min Cool SP 

60

Done

+

-

Changing these settings will affect the operation of the heating/cooling system. To view and edit these settings:
1.  Press the 

MENU button.

2.  Press and hold the two middle buttons simultaneously until the 

Installer Settings menu is displayed.

3.  Scroll to the setting you want to change. Press the plus (+) or minus (-) button to adjust the setting.
4.  Press the 

Done button when you are finished. 

Setting

Range

Default

Description

Display Lock

Y or N

N

Locks or unlocks the thermostat buttons. When the buttons are 
locked, the main menu can still be accessed, but no menu options 
may be selected. The Installer Settings hidden button operation is 
always operational, allowing Display Lock to be turned off. 

System Settings

See next page

Max Heat SP

55F to 90F 
(12C-32C)

90F (32C)

Sets the maximum heating setpoint value. Will not ramp or accept 
setpoints higher than this maximum.

Min Cool SP

 60F to 99F 
(15C-37C)

60F (15C)

Sets the minimum cooling setpoint value. Will not ramp or accept 
setpoints lower than this minimum.

Minimum Run 
Time (MRT)

1- 9 Minutes

3

Sets the minimum run time before a heating/cooling cycle can 
turn off to prevent rapid cycling. Thermostat screen will display 
Cool ON or Heat ON while the minimum run time is being 
enforced.

Minimum Off Time 
(MOT)

5-9 Minutes  

5

Sets the minimum off time before another heating/cooling 
cycle can begin to provide compressor short cycle protection. 
Thermostat screen will display 

WAIT when minimum off time is 

being enforced.

T-Sense

1-6

2

Sample rate of temperature sensor 
Low Sample Rate = Less sensitive (slower response) 
High Sample Rate = More sensitive (faster response)

Fan Cycler 

1

Fan ON Time

0-120 minutes

0 (= OFF)

The fan cycler function cycles the HVAC system fan for an ON 
period followed by an OFF period continuously.  Used to provide 
minimum air ventilation requirements.  While the Fan ON time is 
set to a value greater than 0, an additional Cycler FAN mode is 
present when pressing FAN button.

Fan Cycler 

1

Fan OFF Time

10-120 minutes

10

Remote Sensors

IN or OUT

IN

Used to enable remote temperature sensing, averaging, or for 
outdoor temperature setting for display and/or dual fuel restricted 
mode.

Dehumidification 
Options

See Dehumid Option table

Restore Defaults

n/a

n/a

Sets all of the thermostat settings back to the factory defaults.

 

1  

NOTE: CONTINUOUS fan mode during COOLING operation may not be appropriate in humid climates. If the indoor air exceeds 60% 

relative humidity or simply feels uncomfortably humid, it is recommended that the fan only be used in the AUTO mode.

Installer Settings

Содержание Schlage Link AZEMT500BB32MAA





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды