American Dryer Corp. ML-75HS Скачать руководство пользователя страница 52

Страница: 52 / 56

d. Open main door. The dryer

must stop

and

ALL

output indicator lights on the back side of the micro-

processor (computer) board

must go out

. (Refer to the

illustration

previous page

[

page 46

].)

e. Try to restart the dryer with the main door open.

f. The microprocessor (computer) board's L.E.D. display

must read

DOOR

g. Close the main door and restart the dryer.

h. Functional check of microprocessor (computer) board is complete

a. Upon completing installation of the

replacement Hot Surface Ignition (HSI)

module, reestablish power to the dryer.

b. The HSI module's "red" indicator light

will light up for approximately 5

seconds (self check routine).

If the HSI module's "red" indicator light

stays on or flashes continuously, then the

HSI module is wired incorrectly or has failed.

c. Start the drying cycle.

d. The hot surface ignitor will turn on. After approximately 4 seconds the glo-bar will shut off and the gas

valve will be energized.

The flame should now be established.

e. With the burner flame on, remove the flame sensor wire from the S2 terminal of the HSI module.

The

burner flame must shut off immediately.

f. Stop the drying cycle, with the flame sensor wire still removed, restart the drying cycle.

g. The hot surface ignitor will turn on and after approximately 4 seconds the hot surface ignitor will shut off.

The gas valve will be energized and a burner flame

should be

evident for approximately 7 seconds and

then shut off.

h. The HSI module will attempt two (2) additional ignition trials after which the HSI module will lock out and

the "red" indicator light

will flash continuously.

i. Functional check of the Hot Surface Ignition (HSI) Module is complete.

1) Replace the flame sensor wire from the S2 terminal to the HSI module.

2. Hot Surface Ignition (HSI) System

Содержание ML-75HS

























































Результаты поиска

Содержание ML-75HS

Отзывы:

American Dryer Corp. ML-75HS, Руководство по установке, Страница: 52 / 56

Результаты поиска

Содержание ML-75HS

Отзывы: