American Dryer Corp. ML-75HS Скачать руководство пользователя страница 18

Страница: 18 / 56

E. EXHAUST REQUIREMENTS

1. General Exhaust Duct Work Information

Exhaust duct work

should be

designed and installed by a qualified professional. Improperly

sized duct work will create excessive back pressure which results in slow drying, increased use

of energy, overheating of the dryer, and shutdown of the burner by the airflow (sail) switches,

burner hi-limits, or basket (tumbler) hi-heat thermostats.

CAUTION:

DRYER

MUST BE

EXHAUSTED TO THE OUTDOORS.

CAUTION: IMPROPERLY

SIZED

INSTALLED

EXHAUST

DUCT

WORK

CAN

CREATE

POTENTIAL

FIRE

HAZARD.

The duct work

should be

laid out in such a way that the duct work travels as directly as

possible to the outdoors with as few turns as possible. Single or independent dryer venting is

recommended.

Horizontal Venting:

When single dryer venting is used, the length of duct work, from the dryer to the outside exhaust outlet,

should not

exceed fifteen (15) feet. The minimum diameter of this duct work

must be

at least 10-inches

(even though the dryer exhaust duct for gas and electric units is only 8-inches). In the case of multiple

(common) dryer venting, the distance from the last dryer to the outside exhaust outlet

should not

exceed

fifteen (15) feet. The shape of the duct work is not critical so long as the minimum cross-sectional area is

provided. It is suggested that the use of 90° turns be avoided; use 30° and/or 45° angles instead. The radius

of the elbows

should preferably be

1-1/2 times the diameter of the duct. Including basket (tumbler)/dryer

elbow connections or elbows used for outside protection from the weather, no more than two (2) elbows

should be

used in the exhaust duct run. If more than two (2) elbows are used, the cross sectional area of

the duct work

must be

increased.

ALL

duct work

should be

smooth inside with no projections from sheet

metal screws or other obstructions which will collect lint. When adding ducts, the duct to be added should

overlap the duct to which it is to be connected.

ALL

duct work joints

must be

taped to prevent moisture and

lint from escaping into the building. Inspection doors

should be

installed at strategic points in the exhaust

duct work for periodic inspection and clean-out of lint from the duct work.

Vertical Venting:

When single dryer venting is used the length of the duct work from the dryer to the outside exhaust outlet

should not

exceed twenty (20) feet. The minimum diameter of this duct work

must be

at least 12-inches

(even though the dryer exhaust duct for gas and electric units is only 8-inches) In the case of multiple

(common) dryer venting, the distance from the last dryer to the outside exhaust outlet

should not

exceed

twenty (20) feet. The shape of the duct work is not so critical so long as the minimum cross sectional area is

provided. It is suggested that the use of 90º turns be avoided; use 30º and/or 45º bends instead.. The

radius of the elbows

should preferably be

1-1/2 times the diameter of the duct.

ALL

duct work

should be

smooth inside with no projections from sheet metal screws or other obstructions which will collect lint.

When adding ducts, the duct to be added should overlap the duct to which it is to be connected.

ALL

duct

work joints

must be

taped to prevent moisture and lint from escaping into the building. Inspection doors

should be

installed at strategic points in the exhaust duct work for periodic inspection and clean-out of lint

from the duct work.

IMPORTANT

: Exhaust back pressure measured by a manometer in the exhaust duct should not

exceed 0.3-inches of water column.

Содержание ML-75HS

























































Результаты поиска

Содержание ML-75HS

Отзывы:

American Dryer Corp. ML-75HS, Руководство по установке, Страница: 18 / 56

Результаты поиска

Содержание ML-75HS

Отзывы: