manualshive.com logo in svg

American Dryer Corp. ML-75HS, Руководство по установке, Страница: 5 / 56

Поделиться
Скачать
American Dryer Corp. ML-75HS Скачать руководство пользователя страница 5

Table of Contents

SECTION  I
IMPORTANT INFORMATION ............................................................................... 3

A.  Receiving and Handling ............................................................................................................... 3
B.  Safety Precautions ....................................................................................................................... 3

SECTION  II
SPECIFICATIONS .................................................................................................... 6

A.  Specifications .............................................................................................................................. 6
B.  Component Identification ............................................................................................................. 8

SECTION  III
INSTALLATION PROCEDURES ......................................................................... 10

A.  Location Requirements .............................................................................................................. 10
B.  Unpacking/Setting Up ............................................................................................................... 11
C.  Dryer Enclosure Requirements .................................................................................................. 12
D.  Fresh Air Supply ....................................................................................................................... 13
E.   Exhaust Requirements ............................................................................................................... 14
F.   Electrical Information ................................................................................................................ 19
G.  Gas Information ........................................................................................................................ 27
H.  Steam Information ..................................................................................................................... 30
I.    Preparation For Operation/Start-up .......................................................................................... 36
J.   Preoperational Tests .................................................................................................................. 37
K.  Preoperational Instructions ........................................................................................................ 39
L.  Shut Down Instructions .............................................................................................................. 40

SECTION  IV
SERVICE/PARTS INFORMATION ...................................................................... 41

A.  Service ..................................................................................................................................... 41
B.  Parts ......................................................................................................................................... 41

SECTION  V
WARRANTY INFORMATION .............................................................................. 42

A.  Returning Warranty Card(s) ...................................................................................................... 42
B.  Parts ......................................................................................................................................... 42
C.  Returning Warranty Card(s) ...................................................................................................... 42

Содержание ML-75HS

























































Отзывы:

Нет отзывов