American Dryer Corp. ML-75HS Скачать руководство пользователя страница 24

Страница: 24 / 56

2. ELECTRICAL SERVICE SPECIFICATIONS

A. Gas and Steam Models

IMPORTANT:

Figures shown are for non-reversing models ONLY. For reversing models contact the

factory.

IMPORTANT:

The dryer

must be

connected to the electric supply shown on the data label that is

affixed to the back side of the upper/top control door. In the case of 208 VAC or

230/240 VAC, the supply voltage

must match

the electric service specifications of

the data label exactly.

IMPORTANT:

The wire size

must be

properly sized to handle the related current.

WARNING: 208 VAC and 230/240 VAC ARE NOT THE SAME.

Any damage done to dryer

components due to improper voltage connections will automatically VOID THE

WARRANTY.

NOTE: ADC

reserves the right to make changes in specifications at any time, without notice or

obligation.

MLG-75 (Gas)

MLS-75 (Steam)

LECTRICAL

ERVICE

PECIFICATIONS

(

PER DRYER

)

IMPORTANT: 208 VAC and 230/240 VAC ARE NOT THE SAME. When ordering, specify exact voltage.

NOTE:

A. Fuse ratings are dual-element, time-delay, current limiting, class RK1 or RK5 ONLY.
B. Circuit breakers are thermal magnetic (industrial) type ONLY. For others, calculate/verify correct breaker

size according to appliance amp draw rating and type of breaker used.

Circuit breakers for 3Ø dryers must be 3-pole type.

SERVICE

VOLTAGE

PHASE

WIRE

SERVICE

APPROX.

AMP DRAW

MINIMUM

WIRE SIZE*

FUSING

Dual Element

Time Delay

CIRCUIT

BREAKER

120 (60 Hz)

208 (60 Hz)

3/4

240 (50/60 Hz)

3/4

240 (50/60 Hz)

380-400 (50 Hz)

3/4

416 (50 Hz)

3/4

460 (60 Hz)

3/4

* AWG Stranded Wire ... for individual lenghts less than 100 feet.

Содержание ML-75HS

























































Результаты поиска

Содержание ML-75HS

Отзывы:

American Dryer Corp. ML-75HS, Руководство по установке, Страница: 24 / 56

Результаты поиска

Содержание ML-75HS

Отзывы: