manualshive.com logo in svg

American Dryer Corp. ML-75HS, Руководство по установке, Страница: 25 / 56

Поделиться
Скачать
American Dryer Corp. ML-75HS Скачать руководство пользователя страница 25

21

B.  Electric Models Only

IMPORTANT:

Figures shown are for non-reversing models ONLY.  For reversing models contact the

factory.

IMPORTANT:

The dryer 

must be

 connected to the electric supply shown on the data label that is

affixed to the back side of the upper/top control door.  In the case of 208 VAC or

230/240 VAC, the supply voltage 

must match

 the electric service specifications of

the data label exactly.

IMPORTANT:

The wire size 

must be

 properly sized to handle the related current.

WARNING: 208 VAC and 230/240 VAC ARE NOT THE SAME.  

Any damage done to dryer

components due to improper voltage connections will automatically VOID THE

WARRANTY.

NOTE: ADC

 reserves the right to make changes in specifications at any time, without notice or

obligation.

APPROX.

AMP

 DRA

W

IMPORTANT:

3 phase figures shown are for a 3 wire service ONLY.

MLE-75 (Electric)

E

LECTRICAL 

S

ERVICE 

S

PECIFICATIONS 

(

PER DRYER

)

IMPORTANT:  208 VAC and 230/240 VAC ARE NOT THE SAM E.  When ordering, specify exact vol tage.

NOTE:

A. Fuse ratings are dual-element, time-delay, current limiting, class RK1 or RK5 ONLY.
B. Circuit breakers are thermal magnetic (industrial) type ONLY.  For others, calculate/verify correct breaker size according to appliance amp draw rating and type

of breaker used.

C. Circuit breakers for 3Ø dryers must be 3-pole type.

APPLIED VOLTAGE/PHASE

KW

208/1ø (60 Hz) 240/1ø (50/60 Hz) 208/3ø (50/60 Hz)

240/3ø (50/60 Hz)

380/3ø (50 Hz)

416/3ø (50 Hz)

460/3ø (60 Hz)

20

105

90

-- -

-- -

33

-- -

-- -

24

-- -

-- -

72

63

-- -

36

33

30

-- -

-- -

88

77

-- -

45

41

33

-- -

-- -

-- -

-- -

53

-- -

-- -

36

-- -

-- -

104

92

-- -

53

48

40

-- -

-- -

-- -

-- -

-- -

59

-- -

Содержание ML-75HS

























































Отзывы:

Нет отзывов