American Dryer Corp. ML-75HS Скачать руководство пользователя страница 19

Страница: 19 / 56

IMPORTANT:

Minimum duct work diameter for horizontal venting is 10-inches and for vertical

venting the minimum is 12-inches..

NOTE:

Where the exhaust duct work passes through a wall, ceiling, or roof made of combustible

materials, the opening

must be

2-inches larger (all the way around) than the duct. The duct

must be

centered within this opening.

a. Outside Duct Work Protection

1) To protect the outside end of horizontal duct work from the weather, a 90° elbow bent

downward

should be

installed where the exhaust exits the building. If the duct work

travels vertically up through the roof, it

should be

protected from the weather by using

a 180° turn to point the opening downward. In either case, allow at least twice the diameter of the

duct between the duct opening and the nearest obstruction.

IMPORTANT:

DO NOT

use screens or caps on the outside of opening of exhaust duct work.

2. Single Dryer Venting

Where possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct

should

laid out in such a way that the duct work travels as directly as possible to the outdoors with as few turns

as possible. It is suggested that the use of 90° turns in the ducting be avoided; use 30° and/or 45° angles

instead. The shape of the exhaust duct work is not critical so long as the minimum cross section area is

provided.

IMPORTANT:

Minimum duct size for a dryer that is vented horizontally is 10-inches for a round

duct or an equivalent of 80 square inches.

The DUCT SIZE

MUST NOT

REDUCED ANYWHERE DOWN STREAM OF THE DRYER.

IMPORTANT:

Exhaust back pressure measured by a manometer at each basket (tumbler) exhaust

duct area

should not

exceed 0.3-inches of water column.

IMPORTANT:

Minimum duct size for a dryer that is vented vertically is 12-inches for a round duct or

an equivalent of 120 square inches.

The DUCT SIZE

MUST NOT

REDUCED ANYWHERE DOWN STREAM OF THE DRYER.

Содержание ML-75HS

























































Результаты поиска

Содержание ML-75HS

Отзывы:

American Dryer Corp. ML-75HS, Руководство по установке, Страница: 19 / 56

Результаты поиска

Содержание ML-75HS

Отзывы: