Alto Neptune 5 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 61

Alto Neptune 5 Скачать руководство пользователя страница 49

Neptune_GB_Ver.2.0_10/03

7.

Adjustment / Test

Electronic setup

47.

Service interval setting.

Bridge 3 and 5 on X2 while
changing service interval with the
temperature

adjustment

knob

(100 to 600 hours). Change to
hotwater mode to set new setting.

Pic. 7.1:

Detail of PCB A1

Machine cut off with pressure release.

Function used in connection with remote mode. If “2” is on, machine
switches off after 20 min. in by-pass mode. A restart is only possible with
mainswitch S1. At the same time the ouput of the optional valve Y2 gets
power for 10 s to release pressure at the HP outlet.

Change temperature display.

When “1” is on it shows temperature in

Fahrenheit on

display (NB: it’s not possible to cancel by-pass time when
temp. display is set to Fahrenheit).

°

°

Cancel by-pass time.

Jumper on X10 eliminates by-
pass time of 20 s, which is
necessary

when

adjusting

microswitch B4.

Hour display setting.

Jumper between 2/3 on X9 shows the
total running hours for 5 s on the
display during start-up.

«
...
47
48
49
50
51
...
»

Содержание Neptune 5






























































Отзывы:

Нет отзывов