Alto Neptune 5 Скачать руководство пользователя страница 28

Страница: 28 / 61

Trouble-shooting

Neptune_GB_Ver.2.0_10/03

Display

Symptom

Cause

Outer

Inner

Check

Error codes

Ho S

afety temperature switch B3

opens when temp. is higher than
106 C (222 F).

Wire defective
Use of long hoses at
steam with leaky
valves.

Flow and pressure
switch out of
adjustment.
Oil residue in heat
exchanger.

Heat exchanger
security adjustment.
Switch B3 must be
changed if open.

Detergent valve.

Wire defective.
Spark failure.
Oil filter blocked
soot on glass

O L

ump

il ow

Switch B6 open

Wire defective.

Oil seals worn out

B6 switch

L h

ig t sensor B7 sees ight,

when Y1 is not activated
Flame sensor short circuit
(Cold water operation, not possible)

Sensor not in place.
Wire defective.

Oil residue in heat
exchanger is burning.
Y1 Leaky.
Ignition failure.

Oil pressure.
Nozzle
Electrode
Flame sensor

Ho M

otor

rotector

Motor winding > 160 C(320 F)

Pump pressure too
high.
Temp in room > 40

C (104 F)

Fan on motor
defective.
Fuse (F1)

Sensor in
windings.

ow ailure

Flow switch B2 closed and B4 open.

Wire defective

Reed switch.

No ig t, Fuel

nabled.

Light sensor B7 sees no flame
when Y1 is open.

L h

Flow switch off.

Fuse (F11).
Sensor B7.

mpty.

Level switch B9 Open.

Wire defective

Lea

kage.

Three times start without flow.

Leaky system.

Leaky non-return
valve.

Micro ro essor failure.

p c

Water in electric
system

Temperature

nsor (B1)

pen.

Wire defective.

Temperature

nsor (B1)

losed

Wire defective.

ow switch open (B2) and

microswitch (B4) close.

Air in suction water.
No water.

26.

Flow piston hanging

B4 switch

Содержание Neptune 5






























































Результаты поиска

Содержание Neptune 5

Отзывы:

Alto Neptune 5, Руководство по обслуживанию, Страница: 28 / 61

Результаты поиска

Содержание Neptune 5

Отзывы: