Altigen AltiContact Manager Version 5.0 Скачать руководство пользователя страница 189

Страница: 189 / 542

Board Configuration

AltiContact Manager Administration Manual

6-7

.B
o

Conf

igur

tion

The Board Configuration window contains the following attributes:

Configuring the Triton VoIP Board

Important:

It is strongly recommended that system administrators review

the “Network Configuration Guidelines for VoIP” on page 9-9
before setting up VoIP features.

Parameter

Description

Board Info Group

Board Logical ID: assigned by AltiContact
Manager.

Board Name: the type of board installed in the
system and board ID.

Note: This is informational only and cannot be

edited.

Channel Mapping
List Group

Shows the board Logical Channel, Physical Span,
and Physical Channel.

To reinitialize channels, select the channel to reset
and click the Reset Channel button, then click OK.

Note: This is informational only and cannot be

edited.

Note: Double clicking a channel in this window

invokes a channel configuration window. See
“Triton Analog Trunk Properties” on page 7-
9.

Span Info

Not available for Triton Analog Trunk LS/GS and
LS boards.

Board Configuration

Displays the board’s serial number.

Reset Board

Resets the board, after you confirm resetting by
accepting a warning.

Important:

Resetting a board will disconnect all

calls in progress on that board! Be sure
to inform all users before resetting a
board.

Содержание AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AltiContact Manager Version 5.0

Отзывы:

Бренды по названию

Популярные бренды

Altigen AltiContact Manager Version 5.0, Руководство администратора

Результаты поиска

Содержание AltiContact Manager Version 5.0

Отзывы:

Бренды по названию

Популярные бренды