manualshive.com logo in svg

Alpha Technologies TRI POWER X33 MOD HP 10 kVA, Руководство по эксплуатации и техническому обслуживанию, Страница: 70 / 80

Поделиться
Скачать
Alpha Technologies TRI POWER X33 MOD HP 10 kVA Скачать руководство пользователя страница 70

 

Tri Power X33 Mod HP Manual | Rev 1.20 | © Alpha Technologies GmbH 2013 

70 

8.  Diagnostics 

SIGNALLING EVENTS 

Message

 

Meaning

 

SHUTTING DOWN DUE TO END 
OF AUTONOMY 

UPS shut down due to the end of autonomy. 

SHUTTING DOWN DUE TO 
INCORRECT THREE-PHASE 
SEQUENCE 

UPS shut down due to an incorrect three-phase sequence in input. 

START-UP WITH BATTERY 
FAILED 

Start-up with battery failed. 

BATT.CAL.INTERRUPTED 

Battery calibration interrupted. 

MAXIMUM TIME ON BATTERY 

Maximum time on battery. 

MAXIMUM TIME ON RESERVE 

Maximum time on autonomy reserve. 

START-UP ERROR 

Error in starting up. 

START-UP AUTHORISED WHEN 
THERE ARE ONGOING ALARMS 

UPS start-up authorised in the presence of alarms. 

START-UP AUTHORISED WITH A 
NEW CONFIG. 

UPS start-up authorised with a new confi guration. 

SHUTTING DOWN DUE TO IN-
CORRECT CONFIGURATION 

UPS shutting down due to an incorrect configuration. 

POWER MODULE FW UPDATE 

The Power Module Firmware updated. 

Message

 

Meaning

 

STARTUP BY USER N 

UPS start-up by user. 

SHUTTING DOWN BY USER 

UPS shut down by user. 

AUTOMATIC STARTUP 

Automatic UPS start-up. 

DELAYED SHUTTING DOWN 

The UPS was shut down by programming a delayed shutdown. 

BATTERY CHARGER START IN 
STANDBY 

The battery charger started in standby. 

UPS ON BATTERY 

UPS on battery. 

UPS ON MAINS 

UPS on mains. 

OUTPUT OFF 

The output is off. 

BATTERY TEST EXECUTED 

Batteries tested. 

BATTERIES CALIBRATED 

Batteries calibrated. 

INFORMATION EVENTS 

Содержание TRI POWER X33 MOD HP 10 kVA

















































































Отзывы:

Нет отзывов