Alpha Technologies TRI POWER X33 MOD HP 10 kVA Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 80

Alpha Technologies TRI POWER X33 MOD HP 10 kVA Скачать руководство пользователя страница 25

Tri Power X33 Mod HP Manual | Rev 1.20 | © Alpha Technologies GmbH 2013

25

Operating

a

nd Main

tena

nce

Manua

l

Tri Power X33 Mod HP

4.1

Visual inspection

4. Unpacking and assembly

When the UPS is delivered, examine the packaging and product carefully to see if any damage was done during trans-
port. In particular check the integrity of the indicator on the external ‘Shock Watch’ label.
If either possible or ascertained damage is found report it immediately to:



the carrier;



the ALPHA Assistance Centre.

Make sure that the unit received corresponds to the material specified on the delivery document.
The UPS Tri Power X33 Mod HP packaging protects the equipment against mechanical and environmental damages.
For greater protection it is also wrapped in a transparent
film.

The equipment and relevant accessories supplied (as agreed with the manufacturer) must be in perfect condition.
Before it is shipped the equipment is checked carefully; however, it is always advisable to check it is complete and in
order when receiving it.

Make sure that:



The shipping data (consignee’s address, number of packs, order number, etc.) are the same as those written on
the accompanying documents;



The technical-legal documentation that comes with the equipment includes the user manual for the specific type
of UPS to install together with the CE Declaration of Conformity.

In the case of defects and/or material missing, send a report immediately to the Manufacturer and wait for instruction
before commissioning the equipment.

When  removing  the  packing  material  observe  the
‘ARROW’  on  the  outside  box.  To  remove  the  UPS  from
the packaging follow these steps:

1.  cut the wrapping and open the plastic safety straps;
2.  open the top of the cardboard box;
3.  remove the top protection;
4.  remove the four corner protections;
5.  remove the packaging container, pulling it upwards;

6. remove the pallet and front/rear bracket from the

UPS, loosening the 4 securing screws;

7. inspect the UPS to see if it has been damaged in any

way. Notify the carrier and supplier immediately if
any apparent damage is found.

Keep the packaging material in case the UPS has to be shipped in the future. The packaging materials are 100% recyc-
lable; if you want to dispose of them please comply with the existing laws.

4.1.1 Checking the equipment and accessories supplied

4.2

Unpacking

«
...
23
24
25
26
27
...
»

Содержание TRI POWER X33 MOD HP 10 kVA

















































































Отзывы:

Нет отзывов