Alpha Technologies TRI POWER X33 MOD HP 10 kVA Скачать руководство пользователя страница 55

Страница: 55 / 80

Tri Power X33 Mod HP Manual | Rev 1.20 | © Alpha Technologies GmbH 2013

Operating

nd Main

tena

nce

Manua

Tri Power X33 Mod HP

7.2.1 Status UPS

Modell TRI POWER X33 MOD HP

Equipment model

Info USV

Synchronisation adress

Synchronisation adress of the command

CM-Number

Number of the given command

VA max

Maximum supplaiable apparent power [kVA]

W max

Maximum supplaiable active power [kW]

IBat max

Maximum charge current [A]

SW Vers.

Firmware-Version of UPS

PM SW Vers.

Firmware-Version of Power module

SW Ver.Boot

Version of Bootloaders of UPS

S/N

Serial number of UPS

USV Setup

Inverter

Configuration: 1-phase / 3-phase 120° / 3 single phases

Input

Configuration: 1-phase / 3-phase / 3-phase reverse / not defined

X/X - X/X -X/X

X (count) Power module each phase

No. BCM

no. of installed Power chargers

No. KB

No. of installed battery strings (4 Battery module = 1 string KB)

Batt.Cap.

Battery capacity each battery module

No. each string

total no. of battery blocks 12V each string

Measurements

Power

Active power supplied by UPS on phase X [W]

Output

App.Pow.

Apparent Power supplied by the UPS on phase X [W]

Vrms

Effective voltage supplied by UPS on phase X [V Rms]

Vrms ph-ph Effective line voltage supplied by UPS on phase X [V Rms]

Irms

Effective current supplied by UPS on phase X [A Rms]

Peak I Val.

Peak current supplied in output from the UPS on phase X [A]

Frequency

Frequency of the sinusoid voltage in output from phase X [Hz]

Crest Factor Crest factor of the load connected on phase X

Power factor Power factor of the load connected to the UPS on phase X

W Max

Maximum available active power on phase X [W]

Wirklstg.

actual active power on phase X [W]

VA Max

Maximum available apparent power on phase X [VA]

Scheinlstg.

actual appartent power on phase X [VA]

Note:

To change the phase X press the ENTER key.

Содержание TRI POWER X33 MOD HP 10 kVA

















































































Результаты поиска

Содержание TRI POWER X33 MOD HP 10 kVA

Отзывы:

Alpha Technologies TRI POWER X33 MOD HP 10 kVA, Руководство по эксплуатации и техническому обслуживанию, Страница: 55 / 80

Результаты поиска

Содержание TRI POWER X33 MOD HP 10 kVA

Отзывы: