Aloka ProSound Alpha 10 Скачать руководство пользователя страница 37

Страница: 37 / 405

MN2-2008, Rev.2
SECTION 4

Principle of System Operation

4 - 4

Image Quality Adjustment

B Gain

~Ver.5

30~90dB (60/256 dB Step)

Ver.6.0~

10~90dB (40/256 dB Step)

Possible on both real time and frozen image.

M Gain

±30dB (60/256 dB Step) from B Gain Settings

Possible on both real time and frozen image.

STC

8-level slide variable resistor (0, 1, 2, 3, 5, 8, 12, 18 cm)

* Provided as digital information from the operation
panel.

Ver.3~

Possible to record STC curve for each view durting the
Stress-mode.

Ver.7~

STC Memory (possible to keep the STC curve)

Contrast

16 steps (B, M independent, dB display)
23 steps, Selectable from contrast display (C1~C23) or
dynamic range display (D36~D96, dB)

Possible on both real time and frozen image.

~Ver.4.0

Changed dynamic range against black level.

Ver..4.1~

Changed dynamic range against middle brightness.

AGC

16 steps (B, M independent)

~Ver.3.0

“Relief” and “FTC” function integrate into “AGC”.

Ver.4.0~

“Relief” and “FTC” are independent of “AGC”

FTC (Ver.4.0~)

On/Off

Relief (Ver.4.0~)

OFF/Low/Mid/High

Frame Correlation

16 levels (Both B/W and Color)

Line Correlation

16 levels (Both B/W and Color)

Post Process

5 types (Linear/Slope1/Slope2/Slope3/Reject)

Gamma correction

View Gamma: 5 types (Linear/A/B/C/D)

+ User table: 1 type (User)

Ver.4.1~

View Gamma: 9 types (Linear/A/B/C/D/E/F/G/H)

Scanning line density

Variable in accordance with the diagnostic distance and

zoom settings.

Steered Beam

Max. ±30º (5º steps, special probe only)

Max ±20º (5º steps) for B/W
Flow, Doppler and B/W independent

Image Frequency Select

4 types (High, Resolution, Standard, Penetration)

Image Process Select

Various image quality adjustment change in the lump.

Adaptive Image Processing (Ver.6~)

Speckle noise reduction and Edge enhancement function

Ver.7~

possible to configure parameter mode independent
(the hardware and SOP-ALPHA10-24 are required
depending on S/N)

Edge Optimizer (Ver.6~)

Speckle noise reduction and Edge enhancement function

(the hardware is required depending on S/N)

Image Optimizer (Ver.7~)

Quick adjustment function for B-gain, STC and angle gain

Содержание ProSound Alpha 10






















































































































































































































































































































































































































Результаты поиска

Содержание ProSound Alpha 10

Отзывы:

Aloka ProSound Alpha 10, Руководство по обслуживанию, Страница: 37 / 405

Результаты поиска

Содержание ProSound Alpha 10

Отзывы: