Aloka ProSound Alpha 10 Скачать руководство пользователя страница 145

Страница: 145 / 405

MN2-2008 Rev.1

SECTION 8

Performance Check

8 - 1

8-1

Introduction

Performance Check” describes the items to be confirmed for the maintenance of an equipment quality

and safety under the circumstances referred to below.

Once a repair work has been done,

Once an improvement, for a problem or the like, has been made,

Once a change as to upgrade the functions and/or specifications has been made,

When a periodic inspection is made.

8-2

Attention

CAUTION

During the disk access, DO NOT turn the system power off. If you turn the

system power off during the disk access, All or a part of data on the internal hard

disk will be destroyed.

Unless otherwise specified, this performance check must be conducted with all coverings attached in
place and under the following environments:

30 minutes or more have passed after throwing the stand-by switch ON.

If DICOM network is used, it should be connected properly.

If the performance check specified herein should be conducted after a repair, an improvement or an
upgrade, make certain of the following:

All the PCBs removed are reconnected properly.

All the connectors removed are reconnected properly.

The replaced ROM and others are mounted in place on a printed circuit board.
The power pin, in particular, should NEVER be mistaken for the GND pin.

The unnecessary ROM is NOT left behind inside the equipment.

Tool, measuring probe, and the like are NOT left behind inside the equipment.

Optional components and grounding cable are properly reconnected.

Screws and the like are NOT left behind inside the equipment.

8-3

Making Entries in Repair Report

Upon completion of the check, enter findings thereof in such a form as repair report or the like.

And

present it to the user.

Keep a copy thereof in custody.

Содержание ProSound Alpha 10






















































































































































































































































































































































































































Результаты поиска

Содержание ProSound Alpha 10

Отзывы:

Aloka ProSound Alpha 10, Руководство по обслуживанию, Страница: 145 / 405

Результаты поиска

Содержание ProSound Alpha 10

Отзывы: