Aloka ProSound Alpha 10 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 405

Aloka ProSound Alpha 10 Скачать руководство пользователя страница 34

MN2-2008, Rev.2

SECTION 4

Principle of System Operation

4 - 1

4-1

System Specification

Scanning System

Electronic Linear Scanning
Electronic Convex Scanning
Electronic Sector Scanning
1.5D Array Electronic Linear Scanning
Electronic Convex (3D) Scanning

(the SOP-ALPHA10-4 is required)

Ver.3~

Electronic Sector (3D) Scanning

(the SOP-ALPHA10-4 is required)

Ver.3~

Independent probe (the EU-9110 is required)

Ver.4~

Mechanical Sector Scanning

(the EU-9109 or EU-9124 is required)

Ver.4~

Mechanical Radial Scanning

(the EU-9109 or EU-9124 is required)

Ver.4~

Motorized trans-esophageal probe

Ver.5.1~

Olympus Ultrasonic Gastrovideoscope
(Convex sector type: the SOP-ALPHA10-17 is required)
(Electronic radial type: the SOP-ALPHA10-18 is required)

Simultaneously Attached Probes

Electronic Probe ....... 4 probes

Ver.3~

Independent probe ....1 probe (the EU-9110 is required)

Ver.4~

Mechanical probe .....1 probe

(the EU-9109 or EU-9124 is required)

Operating Modes

B (Fundamental, THE, CHE)
M (Include FAM)
D (PW Doppler, CW Doppler, STCW Doppler)
Flow (Velocity/Variance, Power Flow, TDI)

Ver.2.1~

eFlow (For Lite version, the SOP-ALPHA10-12 is required)
RT-3D (the SOP-ALPHA10-4 is required)

Ver.6.0~

Analog PW Doppler (the hardware is required)

M, D-mode Display

Moving Bar Display (Scrolling is not available)
Sweep Speed: 7 steps

~Ver.4

(17.5, 11.6, 8.7, 5.8, 4.4, 2.9, 2.2 cm/sec)

Ver.5~

(200.0, 150.0, 100.0, 66.7, 50.0, 33.3, 25.0 mm/sec)

Possible on both real time and frozen image.

THE, CHE-mode Display

THE (PHE, ePHD)

CHE (PHD, Harmonic Power Flow, ePHD)

Ver.7~

Transmission with selected MI value

Ver.7~

Direct select function to ePHD mode

Diagnostic Distance

0.5

+

30cm (Each probe has a diagnostic limit)

~Ver.4

1.0cm step (0.5cm step at 0.5cm ~ 2.0cm)
Possible to set selectable range up as each preset

Ver.5~

0.5cm/0.75cm/1.0cm/1.5cm/2.0cm/2.5cm/3.0cm/
3.5cm4.0cm/4.5cm and 1.0 cm step at 5.0cm~.

Notes about expression:

The comments like “Ver.2~” in this document generally means the level
of system in combination of software and hardware. Therefore, some of
specification below may not be applied if only the software is
compatible.

«
...
32
33
34
35
36
...
»

Содержание ProSound Alpha 10






















































































































































































































































































































































































































Отзывы:

Нет отзывов