Alltech 30L100 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 77

background image

KEENAN MechFiber300 Operator’s Manual

35

Revision F01 06

th

March 2020

Yearly (end of season)

Drive chains

:

Remove both chains; wash off all dirt and old oil using paraffin, then
dry. Soak both chains in oil overnight, or longer, if possible.

Idler and auger shaft
front bearing:

Remove and pack with grease.

Machine:

Before storage, wash the complete machine, then grease or oil all
weekly lubrication points as above. Open the drain cock in the
mixing hopper. Check tyre pressures. Store the machine under
cover or under a tarpaulin, if possible.

Electronic weigh box:

If the machine is to be stored, remove the weigh box unit from the
machine and keep in a dry place. Lightly grease the load cell cable
connector end and place it into a plastic bag.

Wheels:

Remove and inspect wheel hub. Replace worn parts, redress and
refit.

Blades:

Blades  need  to  be  kept  sharpened.  This  will  have  to  be  done
without  taking  the  temper  (over-heating)  from  the  blades.  If  the
machine is operated with blunt blades it will cause major stress on
the drive  system.  Blades may have to be replaced when it is not
practical to sharpen them.

10 Specifications

10.1 Weight

Table 8: Machine weights

Note:

1: MechFiber300 weight based on single axle. For a twin axle, add approximately 500 kgs (1,102 lbs.).
2: Weights may vary depending on exact specifications.

WARNING:

Due to hazards involved in entering the mixing chamber it is recommended that all
blade replacement is carried out by a KEENAN authorized service agent who is
specially trained to do this. Contact your local agent (see back cover for details).

Model Weight

MechFiber300

+ Bale handler

Unladen

kgs

6,000

6,250

lbs

13,227

13,778

Payload

kgs

4,200

lbs

9,256

Gross

kgs

10,200

10,450

lbs

22,480

23,031

«
...
33
34
35
36
37
...
»

Содержание 30L100














































































Отзывы:

Нет отзывов

Похожие инструкции для 30L100

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: NORLUX Страницы: 2

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: EarthQuake Страницы: 28

Бренд: TAIKO Audio Страницы: 24

Бренд: Major tech Страницы: 12

Бренд: Waters Страницы: 250

Бренд: Waters Страницы: 141

Бренд: L-Acoustics Страницы: 5

Monkey Jump MM00125

Бренд: M&M Страницы: 2

Бренд: SAC Страницы: 2

Бренд: Tarmo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды