Alltech 30L100 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 77

background image

KEENAN MechFiber300 Operator’s Manual

34

Revision F01 06

th

March 2020

9. Maintenance
Checklist

Daily

Cleaning:

Clean all old feed from around the body to prevent corrosion and
damage to paint.

VFC-Door:

Before using the machine, check that the door opens and shuts
fully and operates smoothly.

Wheel nuts:

Check torque settings

.

Oiler:

Check the oil level and replenish with SAE 10 oil as required.

Weekly (40 hrs)

PTO input shaft:

Grease the universal joints (two nipples) and the sliding half shafts
(smear grease on surfaces). For further information, please refer to
the PTO Maintenance Booklet supplied with the PTO.

Drive (gear) box:

Grease the drive input-shaft bearings (two nipples) and pivot bush
nipple.

Rotor bearings:

Grease the front and rear rotor bearings (two nipples).

Feed discharge auger:

Grease the front and rear auger bearings (two nipples).

Idler shaft:

Grease the front and rear idler shaft bearings (two nipples).

Single axle:

Grease all six pivot points listed below:

Two on each brake rod (four in total)

One on each brake arm (two in total)

Tandem axle

Tandem suspension assembly is fitted with 18 grease fittings:

(where fitted):

Two on each brake rod, one on each pivot (eight altogether)

One on each brake arm (four altogether)
One on each front spring pin (four altogether)
One on each centre spring assembly pivot (two altogether)

Guillotine door (VFC):

Grease the door

’s hydraulic cylinders (four nipples) and the slide

plates (smear food-grade grease on surfaces). The recommended
grease is “Ceran FG” supplied by TOTAL Lubricants, or similar
food- and feed-industry-grade grease.

Drive chains:

Keep the automatic oiler reservoir (where fitted) full of SAE 10 oil.
Check the condition of the two jockey arms.

Tyres:

Check that tyres are inflated to the recommended pressures and
make sure the wheel nuts are tight.

Chain tensions:

Grease the pivot points on the primary and secondary chain
tensioner mechanisms.

Axle U-bolts:

Check axle U-bolt mounting torques (tandem only).

Oiler pipes:

Check hoses for damage or leaks.

Monthly

Bale handler:

Grease each tine pivot and check the tines for looseness.

Tine Buffer:

Check for cracks, splits or degradation.

«
...
32
33
34
35
36
...
»

Содержание 30L100














































































Отзывы:

Нет отзывов

Похожие инструкции для 30L100

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

MicroVersaTrip Plus

Бренд: GE Страницы: 20

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: Walker Bay Страницы: 8

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Backyard Play Systems Страницы: 64

Бренд: Haenim Страницы: 2

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды