Alltech 30L100 Скачать руководство пользователя страница 31

Страница: 31 / 77

KEENAN MechFiber300 Operator’s Manual

Revision F01 06

March 2020

8.7 Nuts and bolts

After the first day, and regularly thereafter, inspect wheel nuts and tandem axle U-bolts
(where fitted).

After the first week, and each week thereafter, check all nuts and bolts, including bearing
nuts, for tightness.

General Torque

Table 6.1: General torque for wheel studs

U-Bolt Diameter (mm)

Tightening Torque (Nm)

230

450

500

600

Table 6.2: Recommended torque for U-bolts for tandem axles (where fitted)

8.8 Tyres

Each week, check the tyres for wear and damage.

Each week, check the tyre pressures. Optimum tyre pressures are shown in Table 7.

This information is given as guidance. If in doubt, please contact KEENAN.

WARNING:

When refitting and re-inflating tyre/wheel assemblies, a safety cage should be used
to prevent possible injury. Incorrectly fitted tyres are dangerous. Please make sure
tyre repairs are carried out by experienced tyre fitters.

Table 7: Tyre pressure

Stud/Bolt type

FT/LB

N.M

M22

335

450

M20

260

350

M18

200

270

Type

Bar

PSI

305 / 55 R 22.5

7.0

110

285 / 70 R 19.5

8.5

125

400 / 60 R 15.5

4.6

385 / 65 R 22.5 (8 stud)

5.5

385 / 65 R 22.5 (10 stud)

9.0

132

Содержание 30L100














































































Результаты поиска

Содержание 30L100

Отзывы:

Похожие инструкции для 30L100

Бренды по названию

Популярные бренды

Alltech 30L100, Руководство оператора

Результаты поиска

Содержание 30L100

Отзывы:

Похожие инструкции для 30L100

Бренды по названию

Популярные бренды