background image

Model LPX1000 

c.p. Allstar Corporation 
Downingtown, PA  19335 
World Wide Web   [email protected]

This Gate Operator is built in the USA and 
complies with all requirements of 
Underwriters' Laboratories Standard UL-325.   
P/N 111785          Rev. D         November 2006

 

PHYSICAL 

 

PAD: 

18-1/4” W x 18-1/4”D x 3”H Elevation 

OVERHEAD CLEARANCE: 

Minimum 25” Required 

UNIT SIZE: 

15”W x 19”D x 24-1/4” H 

FRAME: 

Welded, Uni-Body; Phosphatized And 
Painted to UL Standards 

COVER: 

Architecturally Designed, Rust Free 
LLPE; Key Lock To Prevent 
Unauthorized Access 

SHIPPING WEIGHT: 

115 lbs. 

PRIMARY VOLTAGE: 

115 VAC, 60 Hz, Single Phase 

ELECTRICAL SOURCE: 

One 3-Wire, 15-Amp Service From 
Breaker Panel Required Per Operator 

CONTROL VOLTAGE: 

5 VDC 

RADIO RECEIVER POWER: 

24 VAC, 20 mA 

MOTOR: 

1/2 HP, 4.4 Amp, PSC, Instant Revers-
ing, Thermally Protected (Manual Reset) 

AUTO TIMER-TO-CLOSE: 

Built-In, Adjustable From 2-60 Seconds 

ELECTRICAL 

 

DRIVE 

 

DRIVE SYSTEM: 

Gearbox; 10:1; With Bronze Worm & 
Pinion Gears 

TOTAL SPEED REDUCTION: 

22.2:1 

OUTPUT SHAFT: 

1” dia., Ball-Bearing Mounted 

DRIVE MECHANISM: 

18-Tooth Sprocket; #41 Roller Chain 
30-Tooth Sprocket; #41 Roller Chain 
  High Speed Option, Class III & IV 

LIMITS: 

Independent Open & Close; Displaced 
Cam With Micro-Switch Contacts; 
Adjustable Without Tools 

OPERATOR LOCK: 

Electro-Mechanical, AC Solenoid; 
Engages On Close Limit, Drops Out If 
Power Is Interrupted 

MAX. GATE WEIGHT: 

1,300 lbs., Level Grade 

MAX. GATE WIDTH: 

35 ft.  Maximum Standard 
50 ft. Maximum High Speed Option 
   Class III & IV 

MAX. CYCLES PER HOUR: 

45 Open/Close Per Hour; 800 Open/
Close Per Day (All Calculations Based 
On Typical 20’ Gate On Level Grade) 

GATE SPEED: 

11.8 inches/second 
18 inches/second for High Speed 
   Option (Class III and IV) 

CAPACITIES 

 

Specifications subject to change without notice.  Consult the factory. 

Manufacturer’s Limited Warranty

 

The manufacturer warrants its gate operators to be free from defect in material and workmanship for a period of five (5) years from the date 
of purchase for single family home use and three (3) years from the date of purchase for multi-family and commercial use.  This warranty 
covers all components except the electronic circuit boards which are warranted for three (3) years from the date of purchase for single family 
home use and two (2) years from the date of purchase for multi-family and commercial use.  To obtain service contact your dealer.  

To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from the manufacturer 
before returning the goods.  The goods must be returned with complete identification, with copy of proof-of-purchase, freight prepaid and in 
accordance with the manufacturer’s instructions or they will not be accepted.  In no event will the manufacturer be responsible for goods 
returned without proper authorization or identification. 

Goods returned to the manufacturer for warranty repair within the warranty period, which upon receipt by the manufacturer are confirmed to 
be defective and covered by this limited warranty, will be repaired or replaced at the manufacturer’s sole option, at no cost and returned pre-
paid.  Defective parts will be repaired or replaced with new or factory rebuilt parts at the manufacturer’s sole option. 

This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or 
care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, 
failure to provide reasonable and necessary maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or 
replacement batteries. 

These warranties are in lieu of all other warranties, either expressed or implied.  All implied warranties of merchantability and/or fitness for a 
particular purpose are hereby disclaimed and excluded.  Under no circumstances shall the manufacturer be liable for consequential, incidental 
or special damages arising in connection with the use or inability to use this product.  In no event shall the manufacturer’s liability for breach 
of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby.  No person is authorized to 
assume for the manufacturer any other liability in connection with the sale of this product. 

This warranty gives you specific legal rights.  You may also have other rights which vary from state to state.  Warranty effective after 
October 1, 2003. 

All questions and claims related to the manufacturer’s warranty should be directed to c.p. Allstar Corporation; 443 Boot Road; 
Downingtown, PA  19335; USA (telephone 610-873-6900).

 

 

  TECHNICAL SPECIFICATIONS  

24 

Содержание LEADER PLUS LPX1000 Series

























Отзывы: