MASTER/SLAVE CONFIGURATION
Switch S3 controls the Master/Slave Terminals (#14 & 15)
configuration setting. The setting is used when two control boards
(boxes) are used in conjunction with two mechanical units.
With Switch S3 in the ON position terminals # 6 & 7 (OPEN and
CLOSE inputs) are in the Slave (input) mode and could be coupled to
and would be controlled by a Master control board (box). In the Slave
mode the Switch S1 and S2 must be OFF.
CHECKING THE INDICATOR LIGHTS
There are 16 indicator lights on the control board of the LPX1000
operator. See Figure 22. These lights are used to verify proper
operation of the LPX1000.
TURN ON THE MAIN POWER SWITCH
Remove the white high voltage connector from the control board.
•
Turn all 3 digit switches ON for the test mode.
•
Note that the “POWER” lamp is lighted. This indicates that power
is applied to the control board and the power supply is functioning
•
Connect one end of a short piece of wire (not supplied) to terminal
#16 (COMMON).
•
With the other end of this wire, (make sure that this loose end is free
of insulation), touch the following terminals and observe the noted
response of the lamps.
1.
Manually activate the Close Limit Switch: Close Limit Switch
light is ON.
2.
Manually activate the Open Limit Switch: Open Limit Switch
light is ON.
3.
Connect to Terminal #4, Radio Open.: Radio Open light is ON,
Motor Open light is ON.
4.
Remove wire from Terminal #4, Radio Open. Radio Open light
goes OUT, Motor Open light stays ON.
5.
Connect to Terminal #8, Stop : Both Motor Open and Motor
Close lights are momentarily ON, then both Motor Open and
Motor Close lights go OUT. The Stop Pushbutton light is ON
as long as the wire is held on the terminal and the goes OUT
when the wire is removed.
6.
Connect to Terminal #7, Close.: Observe that the Motor Close
light comes ON and the Close Pushbutton light is ON. Remove
the wire from terminal #7 and observe that the Close Pushbutton
light goes OUT and the Motor Close light stays ON.
7.
Connect to Terminal #11, Reversing Loop,: Observe that both
Motor lights are ON momentarily and then the Motor Close light
goes OUT and the Motor Open light stays ON.
8.
Connect to Terminal #8, Stop,: Same as above, Sequence 5.
9.
Connect to Terminal #3, Alternate: Alternate light is ON, Motor
Close light is ON. Remove wire and note that the Alternate light
goes OUT but the Motor Close light stays ON.
10.
Connect to Terminal #3, Alternate again: Note that the Alternate
light comes ON, that the Motor Close light goes OUT and that
the Motor Open light comes ON.
11.
Connect to Terminal #6, Open: Observe that the Motor Open
light comes ON and the Open Pushbutton light is ON. Remove
the wire from terminal #6 and observe that the Open Pushbutton
light goes OUT and the Motor Open light stays ON.
12.
Connect to Terminal #9, Open Non-contact Sensor: Note that the
Open Non-contact Sensor light comes on & remains on until the
connection is removed. Observe that the both Motor Open and
Motor Close lights are momentarily ON, then the Motor Open
light goes out and the Motor Close light stays on for
approximately 1 second then goes out.
13.
Connect to Terminal #6, Open: Same as above, Sequence #11.
14.
Connect to Terminal #12, Open Contact Sensor: Note that the
Open Contact Sensor light comes on & remains on until the
connection is removed. Observe that the both Motor Open and
Motor Close lights are momentarily ON, then the Motor Open
light goes out and the Motor Close light stays on for
approximately 1 second then goes out.
15.
Connect to Terminal #7, Close: Same as above Sequence #6.
16.
Connect to Terminal #10, Close Non-contact Sensor: Note that
the Close Non-contact Sensor light comes on & remains on until
the connection is removed. Observe that the both Motor Open
and Motor Close lights are momentarily ON, then the Motor
Close light goes out and the Motor Open light stays on for
approximately 1 second then goes out.
17.
Connect to Terminal #7, Close: Same as above Sequence
#6.Connect to Terminal #13, Close Contact Sensor: Note that the
110127
Figure 22: Indicator Lights
INDICATOR LAMPS
D: STARTING THE OPERATOR
15
