background image

TESTING THE VEHICLE LOOP DETECTORS 

1. 

REVERSING LOOP VEHICLE DETECTOR:  

 

Pre-test: 

Pre-test the vehicle detector independently using 

the presence lamp on the front panel of the detector and a 
metal plate over the loop.  When you are satisfied that the 
detector is working properly, connect the loop wires to 
terminals C and D, "REV LOOP",  on the control panel of 
the LPX1000.  More than one loop may be connected to 
terminals C and D if desired, the operator reacts the same 
way  when a vehicle runs over either loop.  

 

  Loop Full Function Test

:  Give the gate an open 

command and allow the close timer to start the gate to 
close.  Place the metal plate over the loop and observe that 
the "REVERSING LOOP" light comes ON the operator 
control board and the gate reopens. 

 

2. 

FREE EXIT VEHICLE DETECTOR:  

 

 

Pre-test

:  Test the vehicle detector independently using 

the presence lamp on the front panel of the detector and a 
metal plate over the loop.  When you are satisfied that the 
detector is working properly, connect the loop wires to 
terminals B and C, "REV LOOP",  on the control panel of 
the LPX1000.

 

 

Loop Full Function Test

:  Place the metal plate over the 

FREE EXIT LOOP and observe that the gate opens to the fully 
open position.  Leave the metal plate on the loop for at least one 
minute.  Observe that the gate does not close.  Remove the plate 
from the loop and observe that the gate closes.  (Some vehicle 
detectors will "tune out" a constant obstruction to the loop after 15 
to 30 minutes.)

 

 TESTING THE VEHICLE LOOP DETECTORS

  

 NOTES

  

20 

Содержание LEADER PLUS LPX1000 Series

























Отзывы: