background image

 

 

Connectors and LEDs 

2-3 

 

SG-9500 Hardware Guide 

 

2.2

 

Rear Panel 

There are two possible configurations of the SG-9500, one that utilizes up to 24 x 
1/10G Ethernet Ports (known as the SG-9500) and another that utilizes 8 x 1/10G 
ports and 4 x 100G ports (known as SG-9500 Configuration B). The configuration 
must be stipulated when ordering. 

 

SG-9500 Configuration A (24 x 1/10G Ports)  

 

 
 

 

Figure 2-4 – SG-9500 (10G) Rear Panel 

Rear Panel Connectors 

 

10G/1G NETWORK/STEERING LINKS 

There are 4 x 1G/10G Ethernet 

network interfaces on each of the six PCIe cards (P1 – P6) which can 
support 1G/10G SFP+ fiber or 1G RJ45 Copper interfaces.  
 

 

 

 

Figure 2-5 – NETWORK/STEERING Links 

Each PCIe card has ports L1-L4 which may be used for either 1G/10G fiber 
or 1G copper network or steering interfaces. On all ports the TX 
connection is on the left and the RX connection is on the right. In the 
NetXplorer, SG-9500 ports are labeled 

Px.Ly 

where 'x' stands for the PCIe 

slot number and 'y' stands for the port number within that PCIe slot. For 
example, the second port on the third PCIe card (S3) will be identified as 
P3.L2. 

MONITOR PORT 

M3  

BYPASS 

POWER SUPPLIES 

M1 

P1 

P2 
P3 

P4 

P5 
P6 

L1 

L2 

L3 

L4 

iLO 

PORT 

M4  

M2 

Содержание SG-9500 Series




























































Отзывы: