Allmand Maxi-Power MP65 T4F Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 76

Allmand Maxi-Power MP65 T4F Скачать руководство пользователя страница 61

Not for

Reproduction

61

Failure and Troubleshooting

51

Troubleshooting

Should any trouble occur during operation, do not leave it. Investigate the cause and take appropriate
measures. Read the manual carefully and fully understand what to do in case of trouble.
The better you understand the construction and function of the machine, the faster you can find a problem
and solution.
This chapter describes the state, cause and countermeasures of important troubles in detail:

Symptom

Cause

Counter measures

Starter does not
rotate.
Low starter revolution
speed even when
starting.

(1)  Battery malfunction
(2)  Charging malfunction
(3)  Alternator malfunction
(4)  Starter malfunction

Check Battery

→

Charge/Change

Change
Change

Starter rotates
normally but engine
does not start up.

(1)  No diesel fuel oil
(2)  Air mixing in fuel piping
(3)  Fuel filter clogging
(4)  Nozzle clogging
(5)  Malfunction of controller

Replenish fuel
Bleed air
Disassemble and clean
Disassemble and clean
Check fuse
Check connector
Check controller

Low engine oil
pressure.

(1)  Engine oil shortage
(2)  Engine oil filter clogging
(3)  Loosened or disconnected wiring, or

connector

(4) Oil pressure switch malfunction

Replenish oil
Change
Check/tightening

Change

High Coolant
temperature

(1)  Shortage of coolant
(2)  Slip of belt
(3)  Radiator clogging
(4)  Faulty thermostat
(5)  Looseness, disconnection of wiring or

connectors

(6) Faulty coolant temperature switch

Replenish
Adjust tension
Clean
Change
Check/tightening

Change

Air filter clogging
monitor lamp glows.

(1) Air filter clogging

Clean

Oil fence lamp.

(1) Condensate accumulated in the oil fence.
(2) Oil fence level sensor is not functioning.

Drain

Check/Change

«
...
59
60
61
62
63
...
»

Содержание Maxi-Power MP65 T4F













































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды