background image

Software Version sb275a05

15

Version sb275a05
C613-10464-00 Rev H

Level 4

No level four issues

Enhancements

CR00012747

File

3

The 

upload

 command (

upload server=

x.x.x.x

 file=

filename.ext

) did 

not allow files with KEY, CER or CSR extensions to be uploaded from the 
switch.

This issue has been resolved, so these file types can now be uploaded.

CR00012786

IP Gateway

3

When a link that had RIP configured on it went down, so that the switch 
used an alternative route, output from the command 

show ip route

 

sometimes displayed incorrect information when the link came back up. 
When the link first comes back up, the route's RIP metric is still 16, so the 
alternative route is still the “best” route to the target. However, 

show ip 

route

 sometimes displayed a disabled route over the original link, with a 

RIP metric of 16, as the best route, even though the switch correctly used 
the alternative route.

This issue has been resolved.

CR

Module

Level

Description

CR

Module

Level

Description

CR00012616

Core, CURE, 

File, Show

-

Monitoring of CPU utilisation has been enhanced. You can now set the 
switch to capture data about which specific functions the CPU is 
executing, and what level of instantaneous usage the CPU is experiencing. 
This allows you, in conjunction with your authorised distributor or reseller, 
to diagnose the causes of high rates of CPU utilisation on the switch.

For more information and the new commands, see “Extended Monitoring 
of CPU Utilisation (CR00012616)” on page 21.

Содержание SwitchBlade 4000 Series























Отзывы: