background image

Software Version sb275a05

13

Version sb275a05
C613-10464-00 Rev H

CR00012726

IP Gateway, 

VLAN, VRRP

2

Previously, if a VLAN had been configured for use as the primary interface 
for a VRID within VRRP, it was possible to delete the VLAN’s IP interface. 
Also, if the IP address of the VLAN was changed (by using the command 

set ip

), the priority of the VRID was not recalculated.

These issues have been resolved, resulting in the following VRRP 
behaviour:

An IP interface cannot be deleted if it is one of the primary interfaces 
already configured for VRRP

An IP interface can still be deleted if it is a monitored interface, because 
VRRP is only monitoring the state of the interface and does not need 
the interface to have an IP address.

A VLAN cannot be destroyed if it is a monitored interface of VRRP.

The command 

set ip

 can be used to change the IP address of the 

interface even if VRRP is active. VRRP will recalculate the priority of the 
specific VRIDs using this interface. However, the IP address of the VRID 
cannot be changed.

CR00012782

Switch, VLAN, 

VRRP

2

If a VRRP interface (including the virtual VRRP MAC address) is elected as 
the VRRP master for a VLAN, and that VLAN has no ports on a given 
switch instance, the VRRP interface is not added to that switch instance. 
This is correct behaviour. However, if a user later added ports to the VLAN 
on that switch instance, the VRRP interface was still not added. This meant 
the switch did not respond to ARP traffic destined for the VRRP MAC 
address if the traffic came via that switch instance. Also, the VRRP 
interface was not always correctly deleted from switch instances.

These issues have been resolved.

CR00012961

Switch

2

In very rare circumstances, the switch rebooted when it attempted to 
update the downstream port members of a layer 3 multicast stream. 

This issue has been resolved.

CR

Module

Level

Description

Содержание SwitchBlade 4000 Series























Отзывы: