background image

Software Maintenance Release Note

Software Version sb275a05
For SwitchBlade 4000 Series Switches

Introduction

This software maintenance release note lists the issues addressed and 
enhancements made in maintenance version sb275a05 for Software Release 
2.7.5A on existing models of SwitchBlade series switches. Release file details 
are listed in 

Table 1

.

This maintenance release note should be read in conjunction with the 
following:

the documentation you received with Software Release 2.7.5A

the SwitchBlade Document Set for Software Release 2.7.3 (Document 
Number C613-03100-00 REV A), available from:
 

www.alliedtelesis.co.nz/documentation/documentation.html

Caution: 

Using a software maintenance version for the wrong model may cause 

unpredictable results, including disruption to the network. 

Information in this release note is subject to change without notice and does not 
represent a commitment on the part of Allied Telesis Inc. While every effort has 
been made to ensure that the information contained within this document and 
the features and changes described are accurate, Allied Telesis Inc. can not 
accept any type of liability for errors in, or omissions arising from the use of this 
information.

Table 1: Release file details for release sb275a05

Maintenance Release Date

7 February 2007

Compressed Release File Name

sb275a05.rez

Compressed Release File Size 

3764560

GUI Resource File Name

d_sb8e29.rsc (8-slot chassis)

d_sb4e29.rsc (4-slot chassis)

Содержание SwitchBlade 4000 Series























Отзывы: