ALLIANCE ALLPH120R410-INV Скачать руководство пользователя страница 19

Страница: 19 / 27

Error code list

Protection/fault

Fault

display

Reason

Elimination methods

Drv1 MOP alarm

F01

MOP drive alarm

Recovery after the 150s

Inverter offline

F02

Frequency conversion board and

main board communication failure Check the communication connection

IPM protection

F03

IPM modular protection

Recovery after the 150s

Comp. Driver Failure

F04

Lack of phase, step or drive
hardware damage

Check the measuring voltage check
frequency conversion board hardware

DC Fan Fault

F05

Motor current feedback open circuit

or short circuit

Check whether current return wires connected motor

IPM Overcurrent

F06

IPM Input current is large

Check and adjust the current measurement

Inv. DC Overvoltage

F07

DC bus voltage>Dc bus over-

voltage protection value

Check the input voltage measurement

Inv. DC Low voltage

F08

DC bus voltage<Dc bus over-
voltage protection value

Check the input voltage measurement

Inv. Input Low voltage.

F09

The input voltage is low, causing
the input current is high

Check the input voltage measurement

Inv. Input Overvoltage.

F10

The input voltage is too high, more
than outage protection current RMS Check the input voltage measurement

Inv. Sampling Volt.

F11

The input voltage sampling fault

Check and adjust the current measurement

Comm. Err DSP-PFC

F12

DSP and PFC connect fault

Check the communication connection

Input Over Cur.

F26

The equipment load is too large

PFC fault

F27

The PFC circuit protection

Check the PFC switch tube short circuit or not

IPM Over heating

F15

The IPM module is overheat

Check and adjust the current measurement

Weak Magnetic Warning

F16

Compressor magnetic force is not

enough

Inv. Input Out Phase

F17

The input voltage lost phase

Check and measure the voltage adjustment

IPM Sampling Cur.

F18

IPM sampling electricity is fault

Check and adjust the current measurement

Inv. Temp. Probe Failure

F19

Sensor is short circuit or open
circuit

Inspect and replace the sensor

Inverter Overheating

F20

Transducer overheat

Check and adjust the current measurement

Inv. Overheating Warning

F22

Transducer temperature is too high Check and adjust the current measurement

Comp. Over Current.

Warning

F23

Compressor electricity is large

The compressor over-current protection

Input Over Cur. Warning

F24

Input current is too large

Check and adjust the current measurement

EEPROM Error Warning

F25

MCU error

Check whether the chip is damaged Replace the chip

V15V over/undervoltage
fault

F28

The V15V is overload or
undervoltage

Check the V15V input voltage in range 13.5v~16.5v or not

Fan Motor2 Fault

F032

Motor is in locked-rotor
state.

The wire connection
between DC-fan motor

module and fan motor is
in bad contact

Change a new fan motor

Check the wire connection and make sure they are in good contact

Communication Fault

(speed control module)

E081 Speed control module and main

board communication fail

Check the communication connection

Содержание ALLPH120R410-INV




























Результаты поиска

Содержание ALLPH120R410-INV

Отзывы:

Похожие инструкции для ALLPH120R410-INV

Бренды по названию

Популярные бренды

ALLIANCE ALLPH120R410-INV, Руководство по установке и эксплуатации

Результаты поиска

Содержание ALLPH120R410-INV

Отзывы:

Похожие инструкции для ALLPH120R410-INV

Бренды по названию

Популярные бренды