ALLIANCE ALLPH120R410-INV Скачать руководство пользователя страница 20

Страница: 20 / 27

Protect/fault

Fault

display

Reason

Elimination methods

Inlet Temp. Sensor Fault

P01

The temp. Sensor is broken or

short circuit

Check or change the temp. Sensor

Outlet Temp. Sensor Fault

P02 The temp. Sensor is broken or

short circuit

Check or change the temp. Sensor

Ambient Temp. Sensor Fault

P04 The temp. Sensor is broken or

short circuit

Check or change the temp. Sensor

Coil 1 Temp. Sensor Fault

P05

The temp. Sensor is broken or
short circuit

Check or change the temp. Sensor

Coil 2 Temp. Sensor Fault

P15

The temp. Sensor is broken or
short circuit

Check or change the temp. Sensor

Suction Temp. Sensor Fault

P07 The temp. Sensor is broken or

short circuit

Check or change the temp. Sensor

Discharge Temp. Sensor

Fault

P081 The temp. Sensor is broken or

short circuit

Check or change the temp. Sensor

Exhaust Air over Temp Prot.

P082 The compressor is overload

Check whether the system of the compressor running normally

Antifreeze Temp. Sensor

Fault

P09

Antifreeze temp sensor is broken or
short circuited

Check and replace this temp sensor

Pressure sensor Fault

The pressure Sensor is broken

Check or change the or pressure

pressure Sensor

High Pressure Prot.

E01 The high-pressure switch is broken Check the pressure switch and cold circuit

Low Pressure Prot.

E02 Low pressure1 protection

Check the pressure switch and cold circuit

Flow Switch Prot.

E03

No water/little water in water
system

Check the pipe water flow and water pump

Waterway Anti-freezing Prot.

E05 Water temp. or ambient temp. is

too low

Inlet and outlet temp. too big E06 Water flow is not enough

and low differential pressure

Check the pipe water flow and whether water system is jammed or not

Anti-freezing Prot.

E07 Water flow is not enough

Check the pipe water flow and whether water system is jammed or not

Winter Primary Anti-freezing
Protection.

E19 The ambient temp. Is low in winter

Winter Secondary Anti-
freezing Prot.

E29

The ambient temp. Is low in winter

Comp. Overcurrent Prot.

E051 The compressor is overload

Check whether the system of the compressor running normally

Communication Fault

E08 Communication failure between

wire controller and mainboard

Check the wire connection between

remote wire controller and main board

Communication Fault

(speed control module)

E081 Speed control module and main

board communication failure

Check the communication connection

Low AT Protection

Ambient temp is too low

EC fan feedback Fault

F051 There is something wrong with fan

motor and fan motor stops running

Check whether fan motor is broken or locked or not

Fan Motor 1 Fault

F031

1. Motor is in locked-rotor state
2.The wire connection between DC-

fan motor module and fan motor is
in bad contact

Change a new fan motor

Check the wire connection and make sure they are in good contact

Содержание ALLPH120R410-INV




























Результаты поиска

Содержание ALLPH120R410-INV

Отзывы:

Похожие инструкции для ALLPH120R410-INV

Бренды по названию

Популярные бренды

ALLIANCE ALLPH120R410-INV, Руководство по установке и эксплуатации

Результаты поиска

Содержание ALLPH120R410-INV

Отзывы:

Похожие инструкции для ALLPH120R410-INV

Бренды по названию

Популярные бренды