Alliance Laundry Systems BD3LLFGS401UW01 Скачать руководство пользователя страница 69

Страница: 69 / 71

513447

Test Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

42. Heater Assembly (Electric

Models)

a. While supporting the access panel, remove two

screws from bottom edge of access panel.

b. Gently lower the access panel to disengage

panel locators from bottom edge of front panel.

c. Disconnect wires from heater assembly.

NOTE: Refer to wiring diagram when rewiring
heater assembly.

d. Set meter to read Ohms. Apply meter probes to

the heater assembly terminals. Meter should
read as follows: (Cold Ohms).

43. Cycling or Limit Thermostat

a. While supporting the access panel, remove two

screws from bottom edge of access panel.

b. Gently lower the access panel to disengage

panel locators from bottom edge of front panel.

c. Label and disconnect wires from thermostat.

NOTE: Refer to wiring diagram when rewiring
thermostat.

Cycling Thermostat (S.P.S.T. – 2 Terminals)

or Limit Thermostat

(1) Set meter to read Ohms.
(2) Apply meter probes to the thermostat

terminals.

(3) Meter should read “zero.”

Cycling Thermostat (S.P.D.T. – 3 Terminals)

(1) Set meter to read Ohms.
(2) Apply meter probes to terminals 1 and 3.

Meter should read “zero”.

(3) Remove screws holding thermostat to

blower fan cover.

(4) Heat thermostat with a small flame until a

distinct “click” is heard, then immediately
apply meter probes to terminals 1 and 2.
Meter should read “zero”.

44. Door Switch

a. While supporting the access panel, remove two

screws from bottom edge of access panel.

b. Gently lower the access panel to disengage

locators from bottom edge of front panel.

c. Remove two screws holding bottom tabs on

front panel to dryer side panels. Swing bottom
of front panel away from dryer far enough to
disengage hold-down clips and locators from
cabinet top.

d. Disconnect wires from door switch.

NOTE: Refer to model wiring diagram when
rewiring door switch.

e. Set meter to read Ohms and apply meter probes

on switch terminals 1 and 3 with door closed.
You should get “zero” reading.

f. Apply probes to terminals 1 and 2 with door

closed. The meter should read “infinite”.

g. Open door. Meter should read “infinite”

between 1 and 3 and “zero” between 1 and 2.

Heater

Element

Color

Code

KW Voltage/Hz. Resistance Reading

Red

240 V 60

Hz.

10.39 ± .31 Ohms Cold

White

4.75

208 V 60

Hz.

8.2 ± .5 Ohms Cold

Green

4.8

240 V 50

Hz.

10.75 ± .32 Ohms Cold

Yellow

240 V 50

Hz.

13.03 ± .39 Ohms Cold

Blue

3.1

240 V 50

Hz.

16.7 ± .5 Ohms Cold

Orange

5.35

240 V 60

Hz.

9.72 ± .3 Ohms Cold

Purple

4.25

208 V 60

Hz.

9.27 ± .3 Ohms Cold

Содержание BD3LLFGS401UW01








































































Результаты поиска

Содержание BD3LLFGS401UW01

Отзывы:

Похожие инструкции для BD3LLFGS401UW01

Бренды по названию

Популярные бренды

Alliance Laundry Systems BD3LLFGS401UW01, Руководство по устранению неисправностей

Результаты поиска

Содержание BD3LLFGS401UW01

Отзывы:

Похожие инструкции для BD3LLFGS401UW01

Бренды по названию

Популярные бренды