Alliance Laundry Systems BD3LLFGS401UW01 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 71

background image

513447

65

Test Procedures

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

36. Electrical Circuit To Ignition

System (Gas Models)

a. While supporting the access panel, remove two

screws from bottom edge of access panel.

b. Gently lower the access panel to disengage

locators from bottom edge of front panel.

c. Close main gas shut-off valve. Refer to

Figure 11

.

d. Remove valve wire harness disconnect block

from the holding and booster coil. Refer to

Figure 31

.

e. Plug dryer power cord into wall receptacle, and

start the dryer in a heat setting (refer to the
Operating Instructions supplied with dryer).

f. Set test meter to read AC voltage and apply

meter probes into terminals on the dryer
harness plug that would correspond to
terminals "1" and "2" on the coil.

Figure 30

.

Meter should register line voltage in all
temperature settings, except FLUFF (NO
HEAT) which should read “zero” VAC.

g. If meter does not read line voltage in step “f”,

check motor switch, thermostats, fabric switch,
accumulator, or timer.

37. Gas Valve Coils Check (Gas

Models)

a. While supporting the access panel, remove two

screws from bottom edge of access panel.

b. Gently lower the access panel to disengage

locators from bottom edge of front panel.

c. Close main gas shut-off valve. Refer to

Figure 11

.

d. Remove disconnect blocks from gas valve

coils.

e. Set test meter to read Ohms and put meter

probes to terminals shown in

Figure 31

, and in

the following chart.

Silicon Carbide Ignition:

COIL TOLERANCE READINGS

Silicon Nitride Ignition:

Both coils should read between 2400-2800
Ohms.

NOTE: If meter registers any other readings than
those listed above, the respective coil(s) should be
replaced.

To reduce the risk of fire, explosion and
electric shock, close the valve in the gas
supply line to the gas dryer and disconnect
the electrical power unless gas or power
supplies are required to perform test
procedure.

W263

WARNING

Meter probes to
terminals:

Meter should read:

50 Hertz

60 Hertz

Holding Coil –
Terminals 1 & 2

1700 ± 285
Ohms

1365 ± 230

Ohms

Booster Coil –
Terminals 1 & 3

685 ± 115

Ohms

560 ± 100

Ohms

Secondary Coil –
Terminals 4 & 5

1680 ± 285
Ohms

1325 ± 230

Ohms

«
...
65
66
67
68
69
...
»

Содержание BD3LLFGS401UW01








































































Отзывы:

Нет отзывов

Похожие инструкции для BD3LLFGS401UW01

Бренд: Haier Страницы: 12

HWD-C1200TXVE-U

Бренд: Haier Страницы: 21

Бренд: Chefman Страницы: 16

Бренд: REVLON Страницы: 32

Бренд: SEVERIN Страницы: 64

Vital System LG-812

Бренд: Zepter Страницы: 16

Бренд: TSM Страницы: 102

BPF SeriesBPF 3540

Бренд: Bakers Pride Страницы: 9

Бренд: Solt Страницы: 2

Бренд: Indesit Страницы: 16

Бренд: Maytag Страницы: 60

Бренд: Galiso Страницы: 14

Profile UPVH890

Бренд: GE Страницы: 152

Profile Harmony PTDN805EM

Бренд: GE Страницы: 76

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 6

131882000 (9907)

Бренд: Frigidaire Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды