Alliance Laundry Systems BD3LLFGS401UW01 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 71

background image

10

513447

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Section 3

Dryer Troubleshooting

IMPORTANT: Refer to wiring diagram for aid in testing dryer components.

1. Dryer Motor Does Not Run

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

Dryer motor does not run.

Is power cord

plugged in?

Plug in cord.

Is electrical power off or fuse

blown? Check laundry room for

blown or loose fuse(s), or open

circuit breaker(s). The dryer itself

doesn't have an electrical fuse.

Yes

Turn power on or
replace fuse. Check
both fuses for
electric models.

Yes

Is loading

door closed?

Close door.

No

Is door switch

inoperative?

Yes

Test switch and
replace if
inoperative.

DRY1845Sa

Yes

No

No

Yes

Refer to
Adjustments
section to
check start
switch and
start windings.
Check for
foreign
objects
jammed in
blower fan.

Are motor

starting

functions

inoperative,

does motor
not start, or

motor just

hum?

No

Is motor dead,

won't run?

Yes

Refer to

Adjustments

section to check start
switch, start windings
and main windings.

Is timer

properly

set?

No

Reset timer or

try another

cycle.

No

Is timer

inoperative?

Test timer and

replace if

inoperative.

Refer to

Test

Procedures

section.

Yes

Yes

No

Has motor

overload

protector

cycled?

Wait two or
three minutes
for overload
protector to
reset. If
protector
cycles
repeatedly,
refer to next
flowchart.

No

Yes

Is motor

centrifugal

switch sticky

or plugged

with lint?

No

Remove
dust or lint
and spray
with a
cleaner and
lubricant.

Yes

Continued on

next page.

No

«
...
10
11
12
13
14
...
»

Содержание BD3LLFGS401UW01








































































Отзывы:

Нет отзывов

Похожие инструкции для BD3LLFGS401UW01

Бренд: JAP Страницы: 68

BISTRO VITAL RA008

Бренд: BOB-HOME Страницы: 24

Бренд: West Bend Страницы: 6

Charmant VT-1342 B

Бренд: Vitek Страницы: 16

Бренд: T3 Страницы: 27

Бренд: Kitchen Advance Страницы: 10

Immortal Power-life

Бренд: Amika Страницы: 23

Бренд: Dean Страницы: 2

Roper REL3612BW2

Бренд: Roper Страницы: 24

Бренд: TCL Страницы: 24

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 9

Бренд: Frigidaire Страницы: 9

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 4

Бренд: CollectraMatic Страницы: 36

Бренд: TriStar Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды