274
Rockwell Automation Publication 1560F-UM001A-EN-P - June 2019
Appendix G
Using DeviceLogix
Table 73 - Bit Output Mapping
Analog Inputs
Available analog inputs to the DeviceLogix program are all 32-bit integers and
include the data points shown in
Table 74 - Analog Input Data Points
The function of the expansion port inputs depends on the card installed in the
given port.
shows how the analog inputs are mapped for each card
type.
Table 75 - Expansion Card Input Mapping
Bit Outputs
Name
Description
(11) Hardware Boolean Outputs
Aux 1, Aux2
Auxiliary Relays available on the control board.
(1)
?
(1) The Auxiliary Relays must be programmed to “Device Logix” to allow the DeviceLogix program to control each specific relay. For
example, if you want to control Aux 1 on the control module you must configure “Aux1 Config” (parameter #172) to “Device
Logix”. Similarly, to control Aux 1 in a Digital I/O (150-SM4) expansion card you must configure “Aux 1 Config” (parameter #6 in
the expansion card) to “Device Logix”.
PX Aux1 – PX Aux3
Auxiliary Relays #1 - #3 available on the Digital I/O
(150-SM4) Expansion Card
(7) Network Boolean Outputs
Coast
Start
Stop
CLR Fault
Emergency Run
Motor Heater
These outputs can be used to control the controller in the
same way a PLC can control the controller. See
for a definition of these control bits.
Analog Inputs
Name
Description
(22) Network Analog Inputs
Volt PP Ave
Average Phase to Phase Voltage (Param #1 - Volts)
I Ave
Average Current (Param #5 – Amps)
Torque
Average Torque (Param #9 - %)
Real Power
Total Real Power (Param #10 – kWatts)
Power Factor
Average Power Factor (Param #17 – in hundredths)
Volt PN Ave
Average Phase to Neutral Voltage (Param #265 – Volts)
Reactive Power
Total Reactive Power (Param #277 – kWatts)
Apparent Power
Total Apparent Power (Param #286 – kWatts)
DLX In 1, DLX In 2
DLX General-purpose Input parameters (Param #335, #336)
DLX DL1 – DLX DL6
DLX Datalink Input Parameters (Param #337-342)
PX In 1 – PX In 2
Analog inputs from the expansion cards – See
Bit Input
Digital I/O
(150-SM4)
Analog I/O (150-SM3) PTC / Grd Fault (150-SM2) Parameter Config
(150-SM6)
PX In 1
None (always 0)
Analog In #1 (Param X.6) Ground Current (Param #11)
None (always 0)
PX In 2
None (always 0) Analog In #2 (Param X.16)
None (always 0)
None (always 0)
Содержание SMC-50
