background image

16

Rockwell Automation Publication 5069-IN003C-EN-P - December 2016

5069 Compact I/O EtherNet/IP Adapters

Connect the Adapter to an EtherNet/IP Network

Use an RJ45 straight cable to connect the adapter to an EtherNet/IP 
network.

1. If needed, wire the RJ45 connector as shown.

2. Connect the RJ45 cable to an Ethernet port on the bottom of 

the adapter. You can connect two RJ45 cables to the adapter.

Install 5069 Compact I/O Modules

Install 5069 Compact I/O modules on the right side of the adapter. 

If the end cap is installed on the adapter, you must remove it before you 
can install the I/O modules.

For more information on how to install 5069 Compact I/O modules, 
see the installation instructions available with each 5069 Compact I/O 
module catalog number.

Install the End Cap

A 5069-ECR end cap is shipped with the adapter.

You must install an end cap on the right side of the last module in a 
5069 Compact I/O system. The end cap covers the exposed 
interconnections on the last module in the system. If you do not install 
the end cap before powering the system, equipment damage or injury 
from electric shock can result.

If the end cap is not installed and you have installed all required 
modules in the system, install the end cap.

1. Align the end cap with interlocking pieces on the adapter.

2. Push the end cap toward the DIN rail until it locks into place.

Power the System

After the end cap is installed on the last module in the system, turn on 
power to the MOD power RTB and the SA power RTB.

WARNING: 

If you connect or disconnect the communication 

cable with power applied to this module or any device on the 
network, an electric arc can occur. This could cause an explosion 
in hazardous location installations.

Be sure that power is removed or the area is nonhazardous 
before proceeding.

This warning applies to connections to ports 1 and 2 on both 

adapters. For more information on where the ports are located 
on the adapter, see 

About the Adapters on page 5

.

Connector 
Number

Color

1585J 8-pin 
Cables with 
Support for 10/
100/1000 Mbps

1585J 8-pin 
Cables with 
Support for 10/
100 Mbps

1585J 4-pin 
Cables with 
Support for 10/
100 Mbps

1

White/

Orange

BI_DA+

2

Orange

BI_DA-

TxData -

3

White/

Green

BI_DB+

Recv Data +

4

Blue

BI_DC+

Unused

N/A

5

White/Blue

BI_DC-

Unused

N/A

6

Green

BI_DB-

Recv Data -

7

White/

Brown

BI_DD+

Unused

N/A

8

Brown

BI_DD-

Unused

N/A

ADAPTER

COMPACT 5000

AENTR

5069-AEN2T

R

Compact I/O

Compact I/O

Top 

Interlocking 
Pieces

End Cap

Bottom 
Interlocking 
Pieces

Top 

Interlocking 
Pieces

End Cap

Bottom 
Interlocking 
Pieces

5069-AEN2TR 
Adapter

5069-AENTR 
Adapter

Содержание Compact I/O 5069 series





















Отзывы: