manualshive.com logo in svg

ALGE-Timing TELEDATA TED-RX, Руководство пользователя, Страница: 30 / 31

Поделиться
Скачать
ALGE-Timing TELEDATA TED-RX Скачать руководство пользователя страница 30

TED-TX / RX

Page 30

6.   TECHNICAL DATA

Frequency:

Standard:

433,500 MHz

Optional:

from 433,050 to 434,790 MHz (in the 70 cm Band)

RF Output Power:

TED-TX10 ................. 10 mW
TED-TX400 ............... 400 mW

Reach:

TED-TX10 ................. about 1,5 km
TED-TX400 ............... about. 5 km

Impulse Input TED-TX:

active low, min. 10 ms, double impulse protection time about 50 ms

Impulse Output TED-RX:

active low, 100 ms

Power Supply:

external:

TED-TX10 and TED-RX: +6,5 to 28 Volt DC
TED-TX400:

+9 to 15 Volt DC

internal:

6 x Alkaline Batteries 1,5 V (type AA) or

6 x NiCd Rechargeable Batteries 1,2 V (type AA)

Power Consumption:

TED-TX10:

in Transmission Mode:

about 35 mA

in Stand-by Mode:

about 3 mA

TED-TX400: in Transmission Mode:

about 300 mA

in Stand-by Mode:

about 3 mA

TED-RX:

Normal Mode:

about 35 mA

Test Mode:

about 70 mA

Working Time:

Table for use with Alkaline Batteries (Type Energizer) at 25°C (77F):

Table for use with NiCd batteries (Type Panasonic 700m Ah) at 25°C (77F):

TED-TX10

without photcell

1 impulse per minute

about 300 hours

TED-TX10

with photocell

1 impulse per minute

about 66 hours

TED-TX10

---

1 data transmission per minute about 270 hours

TED-TX10

---

continues data transmission

about 54 hours

TED-TX400 without photcell

1 impulse per minute

about 270 hours

TED-TX400

with photocell

1 impulse per minute

about 60 hours

TED-TX400

---

1 data transmission per minute about 54 hours

TED-TX400

---

continues data transmission

about 6 hours

TED-RX

---

in all equal

about 54 hours

TED-TX10

without photcell

1 impulse per minute

about 100 hours

TED-TX10

with photocell

1 impulse per minute

about 22 hours

TED-TX10

---

1 data transmission per minute about 90 hours

TED-TX10

---

continues data transmission

about 18 hours

TED-TX400 without photcell

1 impulse per minute

about 90 hours

TED-TX400

with photocell

1 impulse per minute

about 20 hours

TED-TX400

---

1 data transmission per minute about 18 hours

TED-TX400

---

continues data transmission

about 2 hours

TED-RX

---

in all equal

about 18 hours

Содержание TELEDATA TED-RX
































Отзывы:

Нет отзывов