ALGE-Timing TELEDATA TED-RX Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 31

ALGE-Timing TELEDATA TED-RX Скачать руководство пользователя страница 23

TED-TX / RX

Page 23

Version: E-2000-03-02

Page 23

5.1.1. Data Transmission from Timer S4 to Timer S4:

You can supply the TED-TX and TED-RX through the serial interface from the Timer S4
-

TED-TX is supplied by the
Timer S4 with cable 107-10

-

TED-TX is supplied by the
Timer S4 with cable 109-10

You can supply the TED-TX and TED-RX only through the internal batteries with the following

cables:

-

TED-TX and Timer S4 are
connected with cable 010-10

-

TED-TX and Timer S4 are
connected with cable 101-10

Data transmission of a start time from a synchronized Timer S4 to another Timer S4.
-

Use Program 3 for the Timer S4 at the start. You must input the timer of day:
> press yellow and red bottom at the same time
> the display shows "HP 0:00:00"
> Input the hours with the red button
> Input the minutes with the yellow button

-

Use program 0 for the Timer S4 at the finish: You must input the time of day:
> press yellow and red bottom at the same time
> press again yellow and red bottom at the same time
> the display shows "SY 0:00:00"
> Input the hours with the red button
> Input the minutes with the yellow button

-

Synchronize both Timer S4 with a start cable (channel 0)

-

The display of the finish Timer shows the time of day

-

Press yellow and red bottom at the same time to clear the display

-

Program 0 works now as described in the S4 manual

-

Carry the start Timer S4 to the start.

Repeat Data Transmission:

If you do not receive the start time at the finish timer, you can repeat the data transmission:
-

press device-key (10) at TED-TX

-

or press a connected hand switch (banana socket 5 and 6 of TED-TX)

«
...
21
22
23
24
25
...
»

Содержание TELEDATA TED-RX
































Отзывы:

Нет отзывов