manualshive.com logo in svg

ALGE-Timing TELEDATA TED-RX, Руководство пользователя, Страница: 16 / 31

Поделиться
Скачать
ALGE-Timing TELEDATA TED-RX Скачать руководство пользователя страница 16

TED-TX / RX

Page 16

4.  IMPULSE TRANSMISSION

The impulse transmission works direct from any ALGE-impulse trigger to ALGE timer by radio.

Each impulse transmission through the TED

has a constant delay of 0.100 seconds.

Minimum error: 0.001 second

-

If you transmit only the start impulse with the TED you must add to each run time 0.1 seconds.

-

If you transmit only the finish impulse with the TED you must subtract from each run time 0.1
seconds.

-

If you transmit the start- and finish impulse you get the exact run time.

Attention:
For time trail events such as cycling, sking, etc the delay is constant for every competitor. Therefore
you can use a single transmitter without compromising the results. It is only important where you are
trying to measure a record time or speed. Be aware of the limitations of a single transmitter prior to
your event.

The TED-TX and TED-RX is blocked after the beginning of the impulse for 0.1 seconds. This means
each further impulse transmitted with TED-TX is lost during this time.

Double impulse protection:

The TED-TX has a built in
double impulse protection. This
prevents double impulses made
by a bad switch. The double
impulse protection time is 0.05
seconds.

a Contact triggering at the beginning

of the impulse

b Contact triggering at the end of the

impulse

c Duration of impulse plus contact

triggering

d Double impulse protection time (50 ms)
e Double impulse protection time stops, because the 0.05 seconds are not finished

Checking the impulse transmission:

TED-TX:

During the transmission of a timing impulse the LED (3) blinks longer as normal.

TED-RX:

When it receives an timing impulse the LED (3) blinks longer as normal.

Safety of an Impulse Transmission:

When you use the impulse transmission the TED replaces the cable between the impulse trigger
and the timer. You must know, that radio (TED) is easy to disturb. This means that you do not
receive at the timer the signal in case of a disturbance. When you use the TED to transmit the
impulses you will never have the same safety as with wires.

Содержание TELEDATA TED-RX
































Отзывы:

Нет отзывов