background image

10 

L.P.  TANK REQUIREMENTS: 

 

Use only a standard 20 Lbs. (5 Gal.) propane gas cylinder (approx. 12” Ø / 18” tall). The tank must be 

installed  in  the  upright  position.  Do  not  use  a  dented  or  rusty  LP  tank  as  it  may  be  hazardous  and 

should be checked by your LP supplier. Never use a cylinder with a damaged valve.  

 

The LP gas cylinder must be constructed and marked in accordance with the specifications for LP gas 

cylinders  of  the  U.S.  Department  of  Transportation  (DOT)  4BA,  4BW,  and  4E.with  an    ACME  thread/ 

OPD (over fill protection device) installed. 

The cylinder must be provided with a shut off valve terminating in an LP gas supply cylinder valve outlet 

specified,  as  applicable,  for  connection  type 

QCC1

  (CGA-791  or  ACME  threads)  in  the  standard  for 

compressed gas cylinder valve outlet and inlet connections ANSI/CGA V-1.

 

 

LP GAS CONNECTION TO LP TANKS: 

 
Your 

Artisan

™ 

Pizza Oven for use with LP gas comes 

equipped  with  its  own  regulator,  which  MUST  NOT  be 

removed. The oven is shipped with high capacity, hose /

regulator  assembly  for  connection  to  a  standard  20  Lb. 

LP  cylinder.  The  LP  gas  pressure  regulator  and  hose 

supplied with this oven must be used without alteration. 

If this assembly needs to be replaced, use only the type 
specified by 

Artisan

™ 

for this appliance. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pizza ovens require a 60,000 BTUH minimum regulator / hose assembly. 

To connect the regulator / hose assembly follow the next steps: 

 



Locate the regulator and gas connection point in the  rear left side of your 

Oven unit . 

!

 

WARNING

 

KEEP  ANY  ELECTRICAL  CORD 

AND  FUEL  SUPPLY  HOSE  AWAY 

FROM ANY HEATED SURFACES.

 

AVERTISSEMENT

 

GARDER  TOUT  LE  CORDON  ÉLEC-

TRIQUE  ET  LE  TUYAU  D'ALIMENTA-

TION  DE  CARBURANT  À  L'ÉGARD  DE 

TOUTES SURFACES CHAUFFANTES. 

Figure # 5

 

CONNECTION POINT: 

1/2” FPT X 3/8” FLARE 

BRASS FITTING ON 

TYPICAL LP 

GAS TANK 

LP REGULATOR AND HOSE 

ASSEMBLY  (PRESET TO 10” WC) 

ELECTRICAL 

CORD PLUG 

!

 

CAUTION

 

THE  GAS  PRESSURE  REGULATOR  PROVIDED 

WITH  THIS  APPLIANCE  MUST  BE  USED.  RE-

PLACE WITH REGULATOR SES MODEL 220-0280

 

!

 

MISE EN GARDE

 

LE  RÉGULATEUR  DE  PRESSION  DE  GAZ  FOURNI  DE  CE 

APPAREIL  DOIT  ÊTRE  UTILISÉ.  REMPLACER  AVEC  LE  RÉ-

GULATEUR SES MODÈLE 220-0280 

Содержание ARTISAN

































Отзывы: