ALDI Workzone titanium SHW196 Скачать руководство пользователя

Страница: 42 / 56

210cc 4 stroke Petrol High Pressure Washer

AFTER SALES SUPPORT

(toll free)

MODEL No.: SHW196 • 06/2019 9885

e-mail: [email protected]

AUS

1300 889 028

AUS

Deck Cleaning

Pre-rinse deck and surrounding area with fresh water. Apply the

detergent to surface at low pressure. For best results, limit your work

area to smaller sections of approximately 2.3 square meters. Allow

Deck Wash to remain on surface 1-3 minutes. Do not allow detergent

to dry on surface. Rinse at high pressure in a long sweeping motion

keeping the spray nozzle approximately 8-15cm from the cleaning

surface. Always clean from top to bottom and from left to right. When

moving on to a new section of the cleaning surface, be sure to overlap

the previous section to eliminate stop marks and ensure a more even

cleaning result.

Cars, Boats & Motorcycles

Pre-rinse vehicle with fresh water. Apply the detergent to surface at

low pressure. For best results, clean one side of vehicle at a time and

always apply detergent from bottom to top, do not allow detergent to

dry on surface.

If needed, use special wash brush attachment (not included) to remove

stubborn dirt. Rinse at high pressure in a sweeping motion keeping

the spray nozzle approximately 15-20cm from the cleaning surface

(distance should increase when rinsing pin-striping or other sensitive

surfaces). Always clean from top to bottom and from left to right. For

best results, wipe surface dry with a chamois or soft dry cloth.

House Siding

Pre-rinse cleaning surface with fresh water. Apply the detergent

to surface at low pressure (for best results, limit your work area to

sections of approximately 2m and always apply detergent from bottom

to top). Allow detergent to remain on surface 1-3 minutes. Do not

allow detergent to dry on surface, if surface appears to be drying,

simply wet down surface with fresh water. If needed, use special wash

brush attachment (not included) to remove stubborn dirt. Rinse at high

pressure from top to bottom in an even sweeping motion keeping the

spray nozzle approximately 15cm from the cleaning surface.

Working hints for your washer (with or

without detergent)

Содержание Workzone titanium SHW196

























































Результаты поиска

Содержание Workzone titanium SHW196

Отзывы:

Похожие инструкции для Workzone titanium SHW196

Бренды по названию

Популярные бренды

ALDI Workzone titanium SHW196, Руководство пользователя

Результаты поиска

Содержание Workzone titanium SHW196

Отзывы:

Похожие инструкции для Workzone titanium SHW196

Бренды по названию

Популярные бренды