![background image](http://html1.mh-extra.com/html/greenworks/gpw2000-1rg/gpw2000-1rg_quick-start-manual_2263728001.webp)
P0803384-00 Rev B
SPRAY TIP
SPRAY TIP APPLICATION
25
O
Green - Narrow fan tip (25° )
■
The green pressure washer tip provides high versatility with its 25 degree angle tip.
Referred to as the washing tip, because it provides adequate pressure to remove
dirt from surfaces, but is designed to not damage many surfaces. This pressure
washer tip is designed for “sweeping” foliage or debris given its wide angle. This tip
is versatile due to its wide area of cleaning and strong pressure application.
40
O
White - Wide fan tip (40° )
■
The white 40 degree tip, referred to as the “fan” tip creates the widest area of
cleaning with relatively low pressure. This pressure washer tip is best used for light
or delicate cleaning applications. It is recommended for light cleaning on wood
decks and other soft or delicate surfaces.
SOAP
Black - Soap spray tip
■
The black soap spray tip, is used for soap application. Soap is applied under low
pressure high volume for optimum performance. Soap cannot be applied under
high pressure with this machine.
Connect garden hose to pressure
washer water inlet.
Assemble spray gun to spray wand.
Insert high pressure hose into trigger
handle.
Turn on water at outlet.
Run water hose for 30 seconds with the
motor in OFF position. This helps drain air
from the hose and pump.
Connect power cord to wall outlet
Extension cord not recommended.
Turn on Pressure Washer
IMPORTANT:
Ensure water outlet is On
before turning power On to avoid damage
to the pump.
NOTE:
AUTO ON/OFF SWITCH: This Pressure washer is equipped
with an Auto Start/Stop feature.
To operate: Turn the power switch to the On (I) position.
Pump will pressurize and shut down immediately.
Once the trigger of the gun is depressed the unit will turn on.
Unit will shut off and be in standby mode when trigger is
released.
2000 PSI / 1.1 GPM
ELECTRIC PRESSURE WASHER
GPW2000-1RG
This Quick Start Guide is not a substitute for reading the operator's manual. To reduce the risk
of injury or death, user must read and understand operator's manual before using this product.
WARNING:
Set-up
INSTALL THE WHEELS
6
9
Connect desired spray tip.
Connect the high pressure hose to the
water outlet connector.
S
7
2
4
8
30
Insert an axle through the wheel and handle frame.
Insert a cotter pin through the hole of the axle.
Place a washer onto the axle.
5
1
3
INSTALLING THE UPPER HANDLE
■
Push and hold the handle lock buttons on the upper handle.
■
Insert the upper handle into the lower handle until the handle lock
button clicks through the slot.
■
Attach the power cord storage arm onto the fixture.
■
Push the screw through and tighten it with a Phillips Head
Screwdriver (not included.).
INSTALL THE POWER CORD STORAGE ARM
■
Align the screw with the hole in the power cord storage arm.
INSTALL THE SPRAY GUN HOLDER
■
Aligh the screw sleeves of the spray gun holder with the screw holes
on the upper handle.
■
Push the screws through the screw sleeves and tighten them.
?
r
e
t
n
e
c
e
ci
v
r
e
s
a
d
e
e
n
r
o
s
ei
r
o
s
s
e
c
c
a
,
st
r
a
p
g
ni
s
si
M
e
r
o
t
S
o
t
n
r
u
t
e
R
t
o
N
o
D
7
5
7
6
-
9
0
9
-
8
8
8
-
1
:
l
l
a
C
w
w w
n
e
e
r
G
.
W
s
k
r
o
T
m
o
c
.
s
l
o
o