ALDI Workzone titanium SHW196 страница 43 Скачать руководство пользователя

Страница: 43 / 56

210cc 4 stroke Petrol High Pressure Washer

AFTER SALES SUPPORT

(toll free)

MODEL No.: SHW196 • 06/2019 9885

e-mail: [email protected]

AUS

1300 889 028

AUS

Cement Patios, Brick & Stone

Pre-rinse cleaning surface with fresh water. Apply the detergent to

surface at low pressure. For best results, limit your work area to smaller

sections of approximately 2.3 square meters. Allow detergent or

Degreaser to remain on surface 1-3 minutes. Do not allow detergent

to dry on surface. Rinse at high pressure in a sweeping motion keeping

the spray nozzle approximately 8-15cm from the cleaning surface.

Always clean from top to bottom and from left to right.

Barbecue Grills, Outdoor Power Equipment & Gardening Tools

Pre-rinse cleaning surface with fresh water. Apply the detergent at

low pressure. Allow detergent to remain on surface 1-3 minutes. Do

not allow detergent to dry on surface. Rinse at high pressure keeping

the spray nozzle approximately 8-15cm from the cleaning surface. For

removing extremely stubborn dirt, it may be necessary to move the

spray nozzle even closer to the surface for greater dirt cutting action.

Patio & Lawn Furniture

Pre-rinse furniture and surrounding area with fresh water. Apply

the detergent to surface at low pressure. Allow detergent to remain

on surface 1-3 minutes. Do not allow detergent to dry on surface. If

needed use special Wash Brush Attachment (not included) to remove

stubborn dirt. Rinse at high pressure in a sweeping motion keeping the

spray nozzle approximately 8-15cm from the cleaning surface. For best

results, clean from top to bottom and from left to right.

RECOMMENDATIONS

Before cleaning any surface, a separate area should be cleaned to test

spray pattern and distance for maximum cleaning results, as well as the

pressure of the hose and the nozzle.

- When using on surfaces which might come in contact with food,

flush surfaces with plenty of drinking water.

Содержание Workzone titanium SHW196

























































Результаты поиска

Содержание Workzone titanium SHW196

Отзывы:

Похожие инструкции для Workzone titanium SHW196

Бренды по названию

Популярные бренды

ALDI Workzone titanium SHW196, Руководство пользователя

Результаты поиска

Содержание Workzone titanium SHW196

Отзывы:

Похожие инструкции для Workzone titanium SHW196

Бренды по названию

Популярные бренды