manualshive.com logo in svg

ALDI WORKZONE HBS20, Руководство пользователя

Поделиться
Скачать
ALDI WORKZONE HBS20 Скачать руководство пользователя страница 8

13

AFTER SALES SUPPORT

 

 

1300 855 831

 

[email protected]

MODEL: HBS20    PRODUCT CODE: 60339  04/2018

AUS

HBS20

Intended use

IV. Intended use

The bandsaw is designed to perform longitudinal and cross cuts on timber or 

wood-type materials. To cut round materials you must use suitable holding

devices.

The machine is to be used only for its prescribed purpose. This machine is for do-

mestic DIY use only. Any other use is deemed to be a case of misuse. The user / 

operator and not the manufacturer will be liable for any damage or injuries of any 

kind caused as a result of this.

The machine is to be operated only with suitable saw blades. To use the machine 

properly you must also observe the safety regulations, the assembly instructions 

and the operating instructions to be found in this manual.

All persons who use and service the machine have to be acquainted with this 

manual and must be informed about the machine’s potential hazards.

It is also imperative to observe the accident prevention regulations in force in your 

area. The same applies for the general rules of occupational health and safety.

The manufacturer shall not be liable for any changes made to the machine nor for 

any damage resulting from such changes.

Even when the machine is used as prescribed it is still impossible to eliminate 

certain residual risk factors. The following hazards may arise in connection with 

the machine’s construction and design: 

• 

Damage to hearing if ear-muffs are not used as necessary. 

• 

Harmful emissions of wood dust when used in closed rooms. 

• 

Contact with the blade in the uncovered cutting zone. 

• 

Injuries (cuts) when changing the blade. 

• 

Injury from catapulted workpieces or parts of workpieces. 

• 

Crushed fingers. 

• 

Kickback. 

• 

Tilting of the workpiece due to inadequate support. 

• 

Touching the blade. 

• 

Catapulting of pieces of timber and workpieces.

Please note that our machine has not been designed for use in commercial, trade 

or industrial applications. Our warranty will be voided if the machine is used in 

commercial, trade or industrial businesses or for equivalent purposes.

Содержание WORKZONE HBS20































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды