ALDI WORKZONE HBS20 Скачать руководство пользователя страница 24

Страница: 24 / 30

AUS

bgs700

Text

AFTER SALES SUPPORT



1300 855 831



[email protected]

MODEL: HBS20 PRODUCT CODE: 60339 04/2018

XIII. Storage

Store the device and its accessories in a dark, dry and frost-proof place that is in-

accessible to children. The optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust and moisture.

Store the operating manual with the electrical tool.

XIV. Electrical connection

The electrical motor installed is connected and ready for operation. The

connection complies with the applicable Australian standards.

The customer‘s mains connection as well as the extension cable used must

also comply with these regulations.

Important information

In the event of an overloading the motor will switch itself off. After a cool-down pe-

riod (time varies) the motor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often damaged.

This may have the following causes:

•

Passage points, where connection cables are passed through windows or

doors.

•

Kinks where the connection cable has been improperly fastened or routed.

•

Places where the connection cables have been cut due to being driven over.

•

Insulation damage due to being ripped out of the wall outlet.

•

Cracks due to the insulation ageing.

Such damaged electrical connection cables must not be used and are life-threat-

ening due to the insulation damage.Check the electrical connection cables for

damage regularly. Make sure that the power is switched off before inspecting the

cable. Electrical connection cables must comply with the applicable Australian

standards and must be correctly marked. Only use connection cables with the

marking ''H05VV-F''.Replacement cables can only be fitted by an approved and

certified electritian. If you are in any doubt please contact the help line at the foot

of this page.

AC motor

•

The mains voltage must be 230 - 240 V~

•

Extension cables up to 25 m long must have a cross-section of 1.5 mm

Connections and repairs of electrical equipment may only be carried out by an

electrician.

AUS

HBS20

Storage/Electrical connection

Содержание WORKZONE HBS20































Результаты поиска

Содержание WORKZONE HBS20

Отзывы:

Бренды по названию

Популярные бренды

ALDI WORKZONE HBS20, Руководство пользователя

Результаты поиска

Содержание WORKZONE HBS20

Отзывы:

Бренды по названию

Популярные бренды